- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1060ARU (ANALOG DEVICES INC) CON-HDR64POS2ROW 4WALL.1X.1SP,RTANG,LOPF PDF資料下載
參數資料
| 型號： | ADM1060ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | CON-HDR64POS2ROW 4WALL.1X.1SP,RTANG,LOPF |
| 中文描述： | 7-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO28 |
| 封裝： | MO-153AE, TSSOP-28 |
| 文件頁數： | 2/45頁 |
| 文件大?。?/td> | 303K |
| 代理商： | ADM1060ARU |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
ADM1060
–2–
REV. PrJ 11/02
PRELIMINARY TECHNICAL DATA
FEATURES
Faults detected on 7 independent supplies
1 High V oltage supply (up to 14.4V )
4 Positive V oltage Only S upplies (up to 6V )
2 Positive/Negative V oltage supplies (up to +6V OR
down to -6V)
Watchdog Detector Input- Timeout delay programmable
from 200ms to 12.8sec
4 General Purpose Logic Inputs
Programmable Logic Block- combinatorial and sequenc-
ing logic control of all inputs and outputs
9 Programmable Output Drivers
Open Collector (external resistor required)
Open Collector with internal pull-up to V
DD
Fast Internal pull-up to V
DD
Open Collector with internal pull-up to V Pn
Fast Internal pull-up to V Pn
Internally charge pumped high drive (for use with
external N- channel FETS - PDO’s 1 to 4 only)
EEPROM- 512 Bytes
Industry Standard 2- Wire Bus Interface (SMBus)
Guaranteed PDO Low with VPn, VH=1V
A PPLICA T IONS
Central Office Systems
Servers
Infrastructure Network Boards
High density, multi- voltage system cards
G E NE R A L D E SC R IP T ION
T he ADM1060 is a programmable supervisory/sequencing
device which offers a single chip solution for multiple
power supply fault detection and sequencing in communi-
cations systems.
In central office, servers and other infrastructure systems,
a common backplane dc supply is reduced to multiple
board supplies using dc/dc converters. T hese multiple
supplies are used to power different sections of the board
(eg) 3.3V Logic circuits, 5V logic circuits, DSP core and
I/O circuits etc. T here is usually a requirement that cer-
tain sections power up before others (eg) a DSP core to
power up before the DSP I/O or vice versa. T his is in
order to avoid damage, miscommunication or latch- up.
T he ADM1060 facilitates this, providing supply fault
detection and sequencing/combinatorial logic for up to 7
independent supplies. T he 7 Supply Fault Detectors con-
sist of one high voltage detector (up to +14.4V), two bi-
polar voltage detectors (up to +6V OR down to -6V) and
4 positive low voltage detectors (up to +6V). All of the
detectors can be programmed to detect undervoltage, ov-
ervoltage or out- of window (undervoltage OR overvolt-
age) conditions. T he inputs to these Supply Fault
Detectors are via the VH pin (High Voltage), VBn pins
(positive OR negative) and VPn pins (Positive only) pins
respectively. Either the VH supply or one of the VPn
supplies is used to power the ADM1060 (whichever is
highest). T his ensures that, in the event of a supply fail-
ure, the ADM1060 is kept alive for as long as possible,
thus enabling a reliable fault flag to be asserted and the
system to be powered down in an ordered fashion.
Other inputs to the ADM1060 include a Watchdog Detec-
tor (WDI) and 4 General Purpose Inputs (GPIn). T he
Watchdog Detector can be used to monitor a processor
clock. If the clock does not toggle (transition from low to
high or from high to low) within a programmable timeout
period (up to 18 sec.), a fail flag will assert. T he 4 Gen-
eral Purpose inputs can be configured as logic buffers or
to detect positive/negative edges and to generate a logic
pulse or level from those edges. T hus, the user can input
control signals from other parts of their system (eg RE-
SET or POWER_GOOD) to gate the sequencing of the
supplies supervised by the ADM1060.
T he ADM1060 features 9 Programmable Driver Outputs
(PDO
’
s). All 9 outputs can be configured to be logic
outputs, which can provide multiple functions for the end
user such as RESET generation, POWER_GOOD status,
enabling of L DO
’
s, Watchdog T imeout assertion etc.
PDO
’
s 1- 4 have the added feature of being able to pro-
vide an internally charge pumped high voltage for use as
the gate drive of an external N- Channel FET which
could be placed in the path of one of the supplies being
supervised.
All of the inputs and outputs described above are con-
trolled by the Programmable Logic Block Array. T his is
the logic core of the ADM1060. It is comprised of 9
macrocells, one for each PDO. T hese macrocells are
essentially just wide AND gates. Any/all of the inputs can
be used as an input to these macrocells. T he output of a
macrocell can also be used as an input to any macrocell
other than itself (an input to itself would result in a no-
terminating loop). T he PLBA outputs control the PDO
’
s
of the ADM1060 via delay blocks, where a delay of be-
tween 0 and 500ms can be programmed on the rising and/
or the falling edge of the data. T his results in a very flex-
ible sequencing ability. T hus, for instance, PDO1 can be
programmed so that it will not assert until, say, VP2,
VP3and VP4 supplies are in tolerance, VB1 and VH have
been in tolerance for 200mS, and PDO7 has already been
asserted. A simple sequencing operation would be to
daisy chain each PLB output into the input of the next
PLB such that PDO9 doesn
’
t assert until PDO8 asserts,
which in turn doesn
’
t assert until PDO7 asserts etc.
All of the functional capability described here is program-
mable through the industry standard 2 wire bus (SMBus)
provided. Device settings can be written to EEPROM
memory for automatic programming of the device on
power-up. T he EEPROM is organised in 512 bytes, half
of which are used to program all of the functions on the
ADM1060. T he other 256 bytes of EEPROM are for
general purpose system use (eg) date codes, system ID etc.
Read/write access to this is also via the 2 wire interface.
In addition, each output state can be directly overdriven
from the serial interface, allowing a further level of con-
trol (eg) a system controlled soft powerdown.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1064 | Super Sequencer with Voltage Readback ADC |
| ADM1064ACP | Super Sequencer with Voltage Readback ADC |
| ADM1064ACP-REEL | Super Sequencer with Voltage Readback ADC |
| ADM1064ACP-REEL7 | Super Sequencer with Voltage Readback ADC |
| ADM1064ASU | Super Sequencer with Voltage Readback ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1060ARUCS0001R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| ADM1060ARUCS0100R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| ADM1060ARUCS0101R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| ADM1060ARUCS0102R7 | 功能描述:IC SUPERVISOR/SEQUENCER 制造商:analog devices inc. 系列:* 零件狀態:上次購買時間 標準包裝:1 |
| ADM1060ARUCS0103R7 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。