- 您現在的位置：買賣IC網 > PDF目錄374046 > ADV7180 (Analog Devices, Inc.) 10-Bit, 4 x Oversampling SDTV Video Decoder PDF資料下載
參數資料
| 型號： | ADV7180 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| 中文描述： | 10位，4個采樣標清視頻解碼器 |
| 文件頁數： | 19/112頁 |
| 文件大小： | 1320K |
| 代理商： | ADV7180 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
ADV7180
GLOBAL CONTROL REGISTERS
Register control bits listed in this section affect the whole chip.
POWER-SAVING MODES
Power-Down
PDBP, Address 0x0F [2]
The digital supply of the ADV7180 can be shut down by using
the (PWRDWN) pin or via I
2
C (PWRDWN, see below). PDBP
controls whether the I
2
C control or the pin has the higher
priority. The default is to give the pin (PWRDWN) priority.
This allows the user to have the ADV7180 powered down by
default at power-up without the need for an I
2
C write.
When PDBD is 0 (default), the digital supply power is controlled
by the PWRDWN pin (the PWRDWN bit is disregarded).
Rev. A | Page 19 of 112
When PDBD is 1, the PWRDWN bit, 0x0F[5], has priority
(the pin is disregarded).
PWRDWN, Address 0x0F [5]
When PDBP is set to 1, setting the PWRDWN bit switches the
ADV7180 to a chip-wide power-down mode. The power-down
stops the clock from entering the digital section of the chip,
thereby freezing its operation. No I
2
C bits are lost during
power-down. The PWRDWN bit also affects the analog blocks
and switches them into low current modes. The I
2
C interface is
unaffected and remains operational in power-down mode.
The ADV7180 leaves the power-down state if the PWRDWN bit is
set to 0 (via I
2
C) or if the ADV7180 is reset using the RESET pin.
PDBP must be set to 1 for the PWRDWN bit to power down
the ADV7180.
When PWRDWN is 0 (default), the chip is operational.
When PWRDWN is 1, the ADV7180 is in a chip-wide
power-down mode.
RESET CONTROL
RESET, Chip Reset, Address 0x0F [7]
Setting this bit, which is equivalent to controlling the RESET
pin on the ADV7180, issues a full chip reset. All I
2
C registers
are reset to their default/power-up values. Note that some
register bits do not have a reset value specified. They keep their
last written value. Those bits are marked as having a reset value
of x in the register tables (Table 103 and Table 104). After the
reset sequence, the part immediately starts to acquire the
incoming video signal.
After setting the RESET bit (or initiating a reset via the RESET pin),
the part returns to the default for its primary mode of operation.
All I
2
C bits are loaded with their default values, making this bit
self-clearing.
Executing a software reset takes approximately 2 ms. However,
it is recommended to wait 5 ms before any further I
2
C writes are
performed.
The I
2
C master controller receives a no acknowledge condition
on the ninth clock cycle when chip reset is implemented. See
the MPU Port Description section.
When RESET is 0 (default), operation is normal.
When RESET is 1, the reset sequence starts.
GLOBAL PIN CONTROL
Three-State Output Drivers
TOD, Address 0x03 [6]
This bit allows the user to three-state the output drivers of the
ADV7180.
Upon setting the TOD bit, the P15 to P0 (P7 to P0 for the
ADV7180 LFCSP-40), HS, VS, FIELD (VS/FIELD pin for the
ADV7180 LFCSP-40), and SFL pins are three-stated.
The timing pins (HS, VS, FIELD) can be forced active via the
TIM_OE bit. For more information on three-state control, refer
to the Three-State LLC Driver and the Timing Signals Output
Enable sections.
Individual drive strength controls are provided via the
DR_STR_XX bits.
When TOD is 0 (default), the output drivers are enabled.
When TOD is 1, the output drivers are three-stated.
Three-State LLC Driver
TRI_LLC, Address 0x1D [7]
This bit allows the output drivers for the LLC pin of the
ADV7180 to be three-stated. For more information on three-
state control, refer to the Three-State Output Drivers and the
Timing Signals Output Enable sections.
Individual drive strength controls are provided via the
DR_STR_XX bits.
When TRI_LLC is 0 (default), the LLC pin drivers work
according to the DR_STR_C[1:0] setting (pin enabled).
When TRI_LLC is 1, the LLC pin drivers are three-stated.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7180BCPZ | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| ADV7180BSTZ | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| ADV7181 | Multiformat SDTV Video Decoder |
| ADV7181B | Multiformat SDTV Video Decoder |
| ADV7181BBCPZ | Multiformat SDTV Video Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180_12 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder |
| ADV7180BCP32Z | 制造商:Analog Devices 功能描述:10-BIT, 4? OVERSAMPLING SDTV VIDEO DECODER - Trays |
| ADV7180BCP32Z-RL | 制造商:Analog Devices 功能描述:IC |
| ADV7180BCPZ | 功能描述:IC VIDEO DECODER SDTV 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180BCPZ | 制造商:Analog Devices 功能描述:IC VIDEO DECODER 10BIT 57.27MSPS LFCSP40 |
發布緊急采購，3分鐘左右您將得到回復。