- 您現在的位置：買賣IC網 > PDF目錄374046 > ADV7180 (Analog Devices, Inc.) 10-Bit, 4 x Oversampling SDTV Video Decoder PDF資料下載
參數資料
| 型號： | ADV7180 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| 中文描述： | 10位，4個采樣標清視頻解碼器 |
| 文件頁數： | 58/112頁 |
| 文件大小： | 1320K |
| 代理商： | ADV7180 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
ADV7180
Rev. A | Page 58 of 112
Gemstar, PDC, VPS, or UTC
: The user can select to
trigger an interrupt request each time sliced data is
available or to trigger an interrupt request only when
the sliced data has changed. Selection is made via the
GS_VPS_PDC_UTC_CB_ CHANGE bit.
The sequence for the interrupt-based reading of the VDP I
2
C
data registers is as follows for the CCAP standard:
1.
User unmasks CCAP interrupt mask bit (0x50 Bit 0, User
Sub Map = 1). CCAP data occurs on the incoming video.
VDP slices CCAP data and places it into the VDP readback
registers.
2.
The VDP CCAP AVAILABLE bit goes high, and the VDP
module signals to the interrupt controller to stimulate an
interrupt request (for CCAP in this case).
3.
The user reads the interrupt status bits (User Sub Map) and
sees that new CCAP data is available (0x4E Bit 0, User Sub
Map = 1).
4.
The user writes 1 to the CCAP interrupt clear bit (0x4F
Bit 0, User Sub Map = 1) in the interrupt I
2
C space (this is a
self-clearing bit). This clears the interrupt on the INTRQ
pin but does not have an effect in the VDP I
2
C area.
5.
The user reads the CCAP data from the VDP I
2
C area.
6.
The user writes to Bit CC_CLEAR in the VDP_STATUS[0]
register, (0x78 Bit 0, User Sub Map = 1) to signify the CCAP
data has been read (therefore the VDP CCAP can be
updated at the next occurrence of CCAP).
7.
Back to Step 2.
Interrupt Mask Register Details
The following bits set the interrupt mask on the signal from the
VDP VBI data slicer.
VDP_CCAPD_MSKB, Address 0x50 [0], User Sub Map
0 (default)—Disables interrupt on VDP_CCAPD_Q signal.
1—Enables interrupt on VDP_CCAPD_Q signal.
VDP_CGMS_WSS_CHNGD_MSKB, Address 0x50 [2],
User Sub Map
0 (default)—Disables interrupt on VDP_CGMS_WSS_
CHNGD_Q signal.
1—Enables interrupt on VDP_CGMS_WSS_CHNGD_Q
signal.
VDP_GS_VPS_PDC_UTC_CHNG_MSKB,
Address 0x50 [4], User Sub Map
0 (default)—Disables interrupt on
VDP_GS_VPS_PDC_UTC_CHNG_Q signal.
1—Enables interrupt on VDP_GS_VPS_PDC_UTC_CHNG_Q
signal.
VDP_VITC_MSKB, Address 0x50 [6], User Sub Map
0 (default)—Disables interrupt on VDP_VITC_Q signal.
1—Enables interrupt on VDP_VITC_Q signal.
Interrupt Status Register Details
The following read-only bits contain data detection information
from the VDP module since the status bit was last cleared or
unmasked.
VDP_CCAPD_Q, Address 0x4E [0], User Sub Map
0 (default)—CCAP data has not been detected.
1—CCAP data has been detected.
VDP_CGMS_WSS_CHNGD_Q, Address 0x4E [2],
User Sub Map
0 (default)—CGMS or WSS data has not been detected.
1—CGM or WSS data has been detected.
VDP_GS_VPS_PDC_UTC_CHNG_Q, Address 0x4E [4],
User Sub Map
0 (default)—Gemstar, PDC, UTC, or VPS data has not been
detected.
1—Gemstar, PDC, UTC, or VPS data has been detected.
VDP_VITC_Q, Address 0x4E [6], User Sub Map,
Read Only
0 (default)—VITC data has not been detected.
1—VITC data has been detected.
Interrupt Status Clear Register Details
It is not necessary to write 0 to these write-only bits because
they automatically reset after they have been set to 1 (self-
clearing).
VDP_CCAPD_CLR, Address 0x4F [0], User Sub Map
1—Clears VDP_CCAP_Q bit.
VDP_CGMS_WSS_CHNGD_CLR, Address 0x4F [2],
User Sub Map
1—Clears VDP_CGMS_WSS_CHNGD_Q bit.
VDP_GS_VPS_PDC_UTC_CHNG_CLR,
Address 0x4F [4], User Sub Map
1—Clears VDP_GS_VPS_PDC_UTC_CHNG_Q bit.
VDP_VITC_CLR, Address 0x4F [6], User Sub Map
1—Clears VDP_VITC_Q bit.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7180BCPZ | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| ADV7180BSTZ | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| ADV7181 | Multiformat SDTV Video Decoder |
| ADV7181B | Multiformat SDTV Video Decoder |
| ADV7181BBCPZ | Multiformat SDTV Video Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180_12 | 制造商:AD 制造商全稱:Analog Devices 功能描述:10-Bit, 4?? Oversampling SDTV Video Decoder |
| ADV7180BCP32Z | 制造商:Analog Devices 功能描述:10-BIT, 4? OVERSAMPLING SDTV VIDEO DECODER - Trays |
| ADV7180BCP32Z-RL | 制造商:Analog Devices 功能描述:IC |
| ADV7180BCPZ | 功能描述:IC VIDEO DECODER SDTV 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180BCPZ | 制造商:Analog Devices 功能描述:IC VIDEO DECODER 10BIT 57.27MSPS LFCSP40 |
發布緊急采購，3分鐘左右您將得到回復。