- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1761 (NXP Semiconductors N.V.) Hi-Speed Universal Serial Bus On-The-Go controller PDF資料下載
參數資料
| 型號： | ISP1761 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Hi-Speed Universal Serial Bus On-The-Go controller |
| 中文描述： | 高速通用串行總線和On - The - Go控制器 |
| 文件頁數： | 23/158頁 |
| 文件大小： | 724K |
| 代理商： | ISP1761 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
9397 750 13258
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 12 January 2005
23 of 158
Philips Semiconductors
ISP1761
Hi-Speed USB OTG controller
3. Define the IRQ polarity as active LOW or active HIGH in INTR_POL (bit 2) of the HW
Mode Control register. These settings must match the IRQ settings of the host
processor.
By default, interrupt is level-triggered and active LOW.
4. Program the individual Interrupt Enable bits in the HcInterruptEnable register. The
software will need to clear the Interrupt status bits in the HcInterrupt register before
enabling individual interrupt enable bits.
Additional IRQ characteristics can be adjusted in the Edge Interrupt Count register, as
necessary, applicable only when IRQ is set to be edge-active (a pulse of a defined width is
generated every time the IRQ is active).
Bits 15 to 0 of the Edge Interrupt Count register define the IRQ pulse width. The maximum
pulse width that can be programmed is FFFFh, corresponding to a 1 ms pulse width. This
setting is necessary for certain processors that may require a different minimum IRQ
pulse width than the default value. The default IRQ pulse width set at power on is
approximately 500 ns.
Bits 31 to 24 of the Edge Interrupt Count register define the minimum interval between
two interrupts to avoid frequent interrupts to the CPU. The default value of 00h attributed
to these bits determines the normal IRQ generation, without any delay. When a delay is
programmed and the IRQ becomes active after the respective delay, several IRQ events
may have already occurred.
All the interrupt events are represented by the respective bits allocated in the HcInterrupt
register. There is no mechanism to show the order or the moment occurrence of an
interrupt.
The asserted bits in the HcInterrupt register can be cleared by writing back the same
value to the HcInterrupt register. This means that writing logic 1 to each of the set bits will
reset that corresponding bits to the initial inactive state.
The IRQ generation rules that apply according to the preceding settings are:
If an event of interrupt occurs but the respective bit in the Interrupt Enable register is
not set, then the respective HcInterrupt register bit is set but the interrupt signal is not
asserted.
An interrupt will be generated when interrupt is enabled and the respective bit in the
Interrupt Enable register is set.
For a level trigger, an interrupt signal remains asserted until the processor clears the
HcInterrupt register by writing logic 1 to clear the HcInterrupt register bits that are set.
If an interrupt is made edge-sensitive and is asserted, writing to clear the HcInterrupt
register will not have any effect because the interrupt will be asserted for a prescribed
amount of clock cycles.
The clock stopping mechanism does not affect the generation of an interrupt. This is
useful during the suspend and resume cycles, when an interrupt is generated to
signal a wake-up event.
The IRQ generation can also be conditioned by programming the IRQ Mask OR and
IRQ Mask AND registers. Setting some of the bits in these registers to logic 1 will
determine the IRQ generation only when the respective AND or OR conditions of
completing the respective PTDs is met.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1761BE | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP1761ET | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP2100A | Telecommunication IC |
| ISP2100BN4 | Microprocessor |
| ISP2300 | Controller Miscellaneous - Datasheet Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1761BE | 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,518 | 功能描述:USB 接口集成電路 USB HS OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,551 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -T OR NO "-" RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,557 | 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE518 | 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 128LQFP |
發布緊急采購，3分鐘左右您將得到回復。