- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1183BS (NXP SEMICONDUCTORS) Low-power Universal Serial Bus interface device with DMA PDF資料下載
參數資料
| 型號： | ISP1183BS |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Low-power Universal Serial Bus interface device with DMA |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQCC32 |
| 封裝： | 5 X 5 MM, 0.85 MM HEIGHT, PLASTIC, MO-220, SOT-617-1, HVQFN-32 |
| 文件頁數： | 34/62頁 |
| 文件大小： | 295K |
| 代理商： | ISP1183BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
Philips Semiconductors
ISP1183
Low-power USB interface device with DMA
Product data
Rev. 01 — 24 February 2004
34 of 62
9397 750 11804
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
13.2.3
Stall or Unstall Endpoint (40H–4FH/80H–8FH)
These commands are used to stall or unstall an endpoint. The commands modify the
content of the Endpoint Status register (see
Table 26
).
A stalled control endpoint is automatically unstalled when it receives a SETUP token,
regardless of the packet content. If the endpoint should stay in its stalled state, the
microcontroller can restall it with the Stall Endpoint command.
When a stalled endpoint is unstalled (either by the Unstall Endpoint command or by
receiving a SETUP token), it is also reinitialized. This flushes the buffer: if it is an OUT
buffer, it waits for a DATA 0 PID; if it is an IN buffer, it writes a DATA 0 PID.
Code (hex): 40 to 4F —
stall (control OUT, control IN, endpoints 1 to 14)
Code (hex): 80 to 8F —
unstall (control OUT, control IN, endpoints 1 to 14)
Transaction —
none
Remark:
When unstalling a stalled endpoint, issue the unstall command two times.
The first unstall command will update the Endpoint Status register in RAM. The
second unstall command will reset the buffer pointers.
13.2.4
Validate Endpoint Buffer (61H–6FH)
This command signals the presence of valid data for transmission to the USB host, by
setting the Buffer Full flag of the selected IN endpoint. This indicates that the data in
the buffer is valid and can be sent to the host, when the next IN token is received. For
a double-buffered endpoint, this command switches the current FIFO for CPU
access.
Table 27:
Bit
7
Endpoint Status register: bit description
Symbol
Description
EPSTAL
This bit indicates whether the endpoint is stalled or not
(1 = stalled, 0 = not stalled).
Set by a Stall Endpoint command. Cleared by an Unstall
Endpoint command. The endpoint is automatically unstalled on
reception of a SETUP token.
EPFULL1
Logic 1 indicates that the secondary endpoint buffer is full.
EPFULL0
Logic 1 indicates that the primary endpoint buffer is full.
DATA_PID
This bit indicates the data PID of the next packet
(0 = DATA0 PID, 1 = DATA1 PID).
OVERWRITE
This bit is set by hardware. Logic 1 indicates that a new Setup
packet has overwritten the previous setup information, before it
was acknowledged or before the endpoint was stalled. This bit is
cleared by reading, if writing the setup data has finished.
Firmware must check this bit before sending an Acknowledge
Setup command or stalling the endpoint. On reading logic 1, the
firmware must stop ongoing setup actions and wait for a new
Setup packet.
SETUPT
Logic 1 indicates that the buffer contains a Setup packet.
CPUBUF
This bit indicates which buffer is currently selected for CPU
access (0 = primary buffer, 1 = secondary buffer).
-
reserved
6
5
4
3
2
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1301 | Universal Serial Bus On-The-Go transceiver |
| ISP1301BS | Universal Serial Bus On-The-Go transceiver |
| ISP1362 | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362BD | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362EE | Single-chip Universal Serial Bus On-The-Go controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1183BS,118 | 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1183BS,151 | 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1183BS,157 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1183BSFA | 功能描述:IC USB HOST CTRL LOW-SPD 32HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISP1183BS-S | 功能描述:USB 接口集成電路 FULL-SPD USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。