- 您現在的位置：買賣IC網 > PDF目錄382345 > MPC823UM_REV1_16-CPM7 (Motorola, Inc.) 10 AMP SUBMINIATURE POWER RELAY PDF資料下載
參數資料
| 型號： | MPC823UM_REV1_16-CPM7 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 10 AMP SUBMINIATURE POWER RELAY |
| 中文描述： | 通信處理器模塊 |
| 文件頁數： | 14/74頁 |
| 文件大?。?/td> | 234K |
| 代理商： | MPC823UM_REV1_16-CPM7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
Communication Processor Module
16-392
MPC823 REFERENCE MANUAL
MOTOROLA
S
C
1
P
MAX_IDL—Once a character of data is received on the line, the SMCx UART controller
starts counting any idle characters received. If a MAX_IDL number of idle characters is
received before the next data character, an idle timeout occurs and the buffer closes.
This, in turn, produces an interrupt request to the core to receive the data from the
buffer. MAX_IDL provides a convenient way to demarcate frames in SMCx UART
mode. But if you do not want to use MAX_IDL, you must program MAX_IDL to 0x0000
and the buffer will never close, regardless of the number of idle characters received.
The number of bits in an idle character is calculated as follows—1 + character data
length (5 to 14) + 1 (if parity bit is used) + number of stop bits (1 or 2). For example, for
a character data length of 8, no parity, and 1 stop bit, the idle character length is 10 bits.
IDLC—This value is used by the RISC microcontroller to store the current idle counter
value in the MAX_IDL timeout process. IDLC is a down-counter that you do not need to
initialize or access.
BRKLN—This value is used to store the length of the last break character received and
is the bit length of that character. For example, if the receive pin is low for 257 bit times,
BRKLN shows the value 0x0101 and its accuracy comes within one character unit of
bits. For 8 data bits, no parity, 1 stop bit, and 1 start bit, BRKLN is accurate within 10
bits.
BRKEC—This counter counts the number of break conditions that occur on the line.
One break condition can last for hundreds of bit times, yet this counter is only
incremented once during that period.
BRKCR—This value indicates when the SMCx UART controller sends a break
character sequence after a
STOP TRANSMIT
command is issued. The number of
break characters sent by the SMCx UART controller is determined by the value in
BRKCR. For 8 data bits, no parity, 1 stop bit, and 1 start bit, each break character is 10
bits long and consists of all zeros.
R_MASK—This value is a temporary bit mask used internally by the SMCx UART
controller.
16.11.6.5 PROGRAMMING THE SMCx UART CONTROLLER.
The SMCx UART
controller’s data structure supports multibuffer operation and allows you to transmit break
and preamble sequences. Overrun, parity, and framing errors are reported via the buffer
descriptors. In its simplest form, the SMCx UART controller functions in a character-oriented
environment. Each character is transmitted with the stop bits and parity that you configure.
Characters are received into separate 1-byte buffers. A maskable interrupt can be
generated when each buffer is filled.
Many applications may want to take advantage of the message-oriented capabilities that the
SMCx UART controller supports through linked buffers for reception or transmission. You
can handle data in a message-oriented environment and work on entire messages rather
than on a character-by-character basis. A message can span several linked buffers and
each one can be transmitted and received as a linked list of buffers without any intervention
from the core, which makes it easy to program and saves processor overhead. In a
message-oriented environment, the idle sequence is used as the message delimiter. The
transmitter can generate an idle sequence before starting a new message and the receiver
can close a buffer when an idle sequence is found.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC9109 | LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP |
| MPC9229 | 400 MHz Low Voltage PECL Clock Synthesizer |
| MPC9230 | 800 MHz Low Voltage PECL Clock Synthesizer |
| MPC9350 | LOW VOLTAGE PLL CLOCK DRIVER |
| MPC9350D | LOW VOLTAGE PLL CLOCK DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC823VR66B2T | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823VR75B2T | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823VR81B2T | 功能描述:微處理器 - MPU POWER QUICC RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823ZQ66B2T | 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MPC823ZQ75B2T | 功能描述:微處理器 - MPU PORTABLE SYSTEM MPU RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
發布緊急采購，3分鐘左右您將得到回復。