欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: TSB12LV32-EP
英文描述: IC APEX 20KE FPGA 100K 324-FBGA
中文描述: 軍事增強塑料電機及電子學工程師聯合會1394-1995和P1394a兼容通用鏈路層控制器
文件頁數: 23/106頁
文件大小: 605K
代理商: TSB12LV32-EP
2
7
BIT
NUMBER
DESCRIPTION
DIR
FUNCTION
BIT NAME
9
ENA_
INSERT_IDLE
Insert Idle
Enable
R/W
Per P1394a, the link is required to insert an idle state on the
control lines after the Phy grants the link control of the
Phy/link interface. If using a P1394a Phy, this bit should be
set to 1 in order for the link to drive an idle state following the
grant state from the Phy. For 1394-1995 Phys this bit must
remain low.
10
RSTTX
Transmitter
Reset
R/W
When RSTTX is set, the entire transmitter resets
synchronously. This bit clears itself.
11
RSTRX
Receiver
Reset
R/W
When RSTRX is set, the entire receiver resets
synchronously. This bit clears itself.
12
CTNDRSTAT
Contenter
status
R/W
Contender status. On power up, this bit reflects the status of
the CONTNDR pin. When bit 13, CTNDRISIN, is 0 this bit
will be driven out to the CONTNDR pin. If CTNDRISIN is 1
this bit is not used. (Only use on 1394
1995 Phys, or
P1394a Phys when using hardware reset, otherwise, use
the 1394a Phy registers to set the nodes contender status).
13
CTNDRISIN
Contender
Driver Enable
R/W
Driver enable for the CONTNDR pin. On power up this bit is
set to 1 which disables the driver and allows reading of the
state of the CONTNDR pin. Writing a 0 to this bit will enable
the driver and will drive bit 12, CTNDRSTAT, to the
CONTNDR pin.
14
RESERVED
Reserved
15
BUSNRST
Bus number
reset enable
R/W
When this enable is set to high, the bus number field clears
to 3FFh when a local bus reset is received.
16
17
BDIV0, BDIV1
BCLK divisor
encode bits
R/W
BCLK divisors encode bits. Used to divide down the BCLK
to generate the link power status (LPS) clock to the Phy.
BDIV0
0
BDIV1
0
DESCRIPTION
Divide by 16. Default power on value.
Recommended for BCLK frequencies in
the range of 8
88 MHz.
0
1
Divide by 2. Recommended for BCLK
frequencies in the range of 1
11 MHz.
1
0
Divide by 4. Recommended for BCLK
frequencies in the range of 2
22 MHz.
1
1
Divide by 32. Recommended for BCLK
frequencies in the range of 16
176
MHz
18
DMACKCOMP
Data Mover
Acknowledge
Complete
R/W
Data mover acknowledge complete. This bit controls the
acknowledge response to an asynchronous packet
received and routed to the DM port. The default and power
on value is 0 which means to respond with ack pending. A 1
means to respond with an ack complete for write request
packets.
19
FIFOACKCOMP
FIFO
Acknowledge
Complete
R/W
FIFO acknowledge complete. This bit controls the
acknowledge response to an asynchronous packet
received and routed to the GRF. The default and power on
value is 0 which means to respond with ack pending. A 1
means to respond with ack complete.
相關PDF資料
PDF描述
TSB12LV01B-EP FPGA (Field-Programmable Gate Array)
TSB12LV01BPZ FPGA (Field-Programmable Gate Array)
TSB12LV26-EP 672-pin FineLine BGA
TSB12LV22PZP OHCI-Lynx PCI-BASED IEEE 1394 HOST CONTROLLER
TSB12LV26PZ OHCI-Lynx PCI-BASED IEEE 1394 HOST CONTROLLER
相關代理商/技術參數
參數描述
TSB12LV32I 制造商:TI 制造商全稱:Texas Instruments 功能描述:IEEE 1394-1995 and P1394a Compliant General-Purpose Link-Layer Controller
TSB12LV32IPZ 功能描述:1394 接口集成電路 General-Purpose Link Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB12LV32IPZEP 制造商:Texas Instruments 功能描述:1394 I-TEMP 1394 GENERAL-PURPOSE LINK LAYER CONTROLLER (GP2L - Rail/Tube
TSB12LV32IPZG4 功能描述:1394 接口集成電路 General Purpose Link Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
TSB12LV32PZ 功能描述:1394 接口集成電路 General-Purpose Link Layer Cntrlr RoHS:否 制造商:Texas Instruments 類型:Link Layer Controller 工作電源電壓: 封裝 / 箱體:LQFP 封裝:Tray
主站蜘蛛池模板: 特克斯县| 普宁市| 巩留县| 金湖县| 巫溪县| 交城县| 集贤县| 如东县| 沂南县| 南昌县| 东丰县| 左贡县| 合川市| 木兰县| 定结县| 青冈县| 榆中县| 上栗县| 普宁市| 阿尔山市| 东光县| 东莞市| 瓮安县| 巴林左旗| 浠水县| 太白县| 都安| 紫云| 云林县| 健康| 天水市| 木兰县| 体育| 广宗县| 昌宁县| 株洲县| 长春市| 贡山| 南岸区| 黄骅市| 眉山市|