- 您現在的位置：買賣IC網 > PDF目錄365968 > TSB14AA1T FPGA (Field-Programmable Gate Array) PDF資料下載
參數資料
| 型號： | TSB14AA1T |
| 英文描述： | FPGA (Field-Programmable Gate Array) |
| 中文描述： | 電信提供商/數據通信 |
| 文件頁數： | 19/35頁 |
| 文件大?。?/td> | 224K |
| 代理商： | TSB14AA1T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
5
–
2
–
When the designer must choose a backplane transceiver logic (BTL) transceiver, the FutureBus+
transceiver SN74FB2041A [6] is recommended.
–
When the designer must choose a VERSA module Eurocard (VME) bus transceiver, the VME1395 is
recommended (to be released).
–
When the designer must choose a high speed 5-V transistor-transistor logic (TTL) transceiver, the
SN74BCT756 [7] is recommended.
Refer to application report
TSB12LV01B/TSB14AA1A Reference Schematic
[8]
and application report
TSB14AA1A/Transceivers Reference Schematic [9] for more information.
5.2
Link Selection
The system designer must select links appropriate for the TSB14AA1A and the host interface selected. The following
are requirements for the LLCs needed:
Using the TSB14AA1A at 100 Mbits/s, any 1394 cable link layer can be used.
Using the TSB14AA1A at 50 Mbits/s, it is appropriate to use the TSB12LV01B, TSB12LV32 (GP2Lynx), or
TSB12LV21B (PCILynx), depending on the host-link interface. For example:
–
TSB12LV01B has a 32-bit data bus and is used most appropriately with a host that has 32 or 64-bit data
bus.
–
TSB12LV32 is designed for interface with a Motorola-type microprocessor and should be used for an 8
or 16-bit host.
–
TSB12LV21B is best used if the host is the PCI bus.
It is necessary to verify that the CLK on the PHY-link interface is faster than the CLK on the link-host interface, based
on LPS low time and detecting SCLK.
5.3
Layout Recommendation
A local clock (either 98.304 MHz for S100, or 49.152 MHz for S50) is used for the synchronization of the TSB14AA1A
state machine within the PHY logic. The source of this clock must be placed as close as possible to PHY pin XI. The
greater the distance, the more the chance of interference from noise. The local clock reference signal is internally
divided to provide the clock signals used to control transmission of the outbound encoded strobe and data information
and system clock (SCLK) sent to the link layer to synchronize the PHY-link interface.
The PHY-link interface (SCLK, LREQ, CTL[0,1], and D[0,1]) must be short (less than 4 inches if practical). The signals
driven across the PHY-link interface are at 3.3 V, but are at 49.152 MHz and should be treated with due care. These
signals should also be approximately the same length. The short distance is to minimize noise coupling from other
devices and signal loss due to resistance. They should be kept the same length to reduce propagation delay
mismatches across this synchronous interface. Refer to
Recommendations for PHY Layout
[10] for more information.
The TSB14AA1A requires an external 98.304-MHz reference oscillator input for S100 operation or 49.152-MHz for
S50 operation. Because of the frequencies involved (up to 49.152 MHz system clock at 100 Mbps) the etches
propagating the DATA and STRB signal in the backplane should be treated as transmission lines.
[6]
SN74FB2041A, 7
–
Bit TTL/BTL Transceiver
data sheet (SCBS172J)
(7] SN74BCT756,
Octal Buffer/Driver With Open-Collector Inputs
(SCBS056B)
[8]
TSB12LV01B/TSB14AA1A Reference Schematic (SLLS465)
[9]
TSB14AA1A/Transceivers Reference Schematic
()
[10]
Recommendations for PHY Layout
(SLLA020A)
相關PDF資料 |
PDF描述 |
|---|---|
| TSB14C01MHV | IC APEX 20KE FPGA 160K 484-FBGA |
| TSB14C01HV | 5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
| TSB21LV03MHV | IC APEX 20KE FPGA 200K 484-FBGA |
| TSB21LV03CHV | IEEE 1394-1995 TRIPLE-CABLE TRANSCEIVER/ARBITER |
| TSB2203X6MMX30M | IC APEX 20KE FPGA 200K 240-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSB14AA1TPFB | 功能描述:IC BACKPLANE PHY 3.3V 48-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| TSB14C01 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
| TSB14C01A | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
| TSB14C01AI | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
| TSB14C01AIPM | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V IEEE 1394-1995 BACKPLANE TRANSCEIVER/ARBITER |
發布緊急采購，3分鐘左右您將得到回復。