- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCT7491RQR2G (ON Semiconductor)IC REMOTE THERMAL MONITOR 24QSOP Datasheet資料下載
參數資料
| 型號： | NCT7491RQR2G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 53/80頁 |
| 文件大小： | 844K |
| 描述： | IC REMOTE THERMAL MONITOR 24QSOP |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
NCT7491
http://onsemi.com
53
Table 64. REGISTER 0x40 Configuration Register 1 (PowerOn Default = 0x84)
Bit
Name
R/W
Description
<0>
STRT
(Notes 18, 19)
R/W
Logic 1 enables monitoring and PWM control outputs based on the limit settings programmed.
Logic 0 disables monitoring and PWM control is based on the default powerup limit settings.
Note that the limit values programmed are preserved even if a Logic 0 is written to this bit and
the default settings are enabled. This bit does not become locked once Bit 1 (LOCK bit) has
been set.
<1>
LOCK
Write once
Logic 1 locks all limit values to their current settings. Once this bit is set, all lockable registers
become readonly and cannot be modified until the NCT7491 is powered down and powered
up again. This prevents rogue programs such as viruses from modifying critical system limit
settings. (Lockable.)
<2>
RDY
R
This bit is set to 1 by the NCT7491 to indicate that the device is fully poweredup and ready
to begin system monitoring.
<3>
Fan Boost
R/W
When this bit is set to logic 1 all PWM outputs go to 100% regardless of other fan speed
configurations and automatic fan speed control settings. When this bit is set to 0 the fan
speed control returns to the fan speed setting calculated by the preprogrammed fan speed
control settings. This bit remains writable after the lock bit is set.
<4>
PECI Monitor
R/W
Set this bit to logic 1 to enable CPU thermal monitoring via PECI interface. This bit becomes
read only when the lock bit is set.
<5>
THERM
Override
R/W
When this bit is set to logic 1, any THERM
pin assertion will cause the fans to go to 100% or
Max PWM, depending on bits <4:2> of register 0x16, overriding any other fan setting, even
when the PWMs are configured for manual mode, or disabled. This bit becomes read only
when the lock bit is set.
<7:6>
AVELN
R/W
Sets the averaging length for all analog channels
00 = 4 readings per averaged value
01 = 8 readings per averaged value
10 = 16 readings per averaged value
11 = 32 readings per averaged value
18.Bit 0 (STRT) of Configuration Register 1 (0x40) remains writable after lock bit is set.
19.When monitoring (STRT) is disabled, PWM outputs always go to 100% for thermal protection.
Table 65. REGISTER 0x41 Interrupt Status Register 1 (PowerOn Default = 0x00)
Bit
Name
R/W
Description
<0>
2.5 V
R
2.5 V = 1 indicates that the 2.5 V high or low limit has been exceeded. This bit is cleared on a read of
the status register only if the error condition has subsided.
<1>
V
CCP
R
V
CCP
= 1 indicates that the V
CCP
high or low limit has been exceeded. This bit is cleared on a read of
the status register only if the error condition has subsided.
<2>
V
CC
R
V
CC
= 1 indicates that the V
CC
high or low limit has been exceeded. This bit is cleared on a read of
the status register only if the error condition has subsided.
<3>
5 V
R
A 1 indicates that the 5 V high or low limit has been exceeded. This bit is cleared on a read of the
status register only if the error condition has subsided.
<4>
RIT
R
RIT = 1 indicates that the Remote 1 low or high temperature has been exceeded. This bit is cleared
on a read of the status register only if the error condition has subsided.
<5>
LT
R
LT = 1 indicates that the local low or high temperature has been exceeded. This bit is cleared on a
read of the status register only if the error condition has subsided.
<6>
R2T
R
R2T = 1 indicates that the Remote 2 low or high temperature has been exceeded. This bit is cleared
on a read of the status register only if the error condition has subsided.
<7>
OOL
R
OOL = 1 indicates that an outoflimit event has been latched in Status Register 2. This bit is a logic-
al OR of all status bits in Status Register 2 (0x42). Software can test this bit in isolation to determine
whether any of the voltage, temperature, or fan speed readings represented by Status Register 2 are
outoflimit, which eliminates the need to read Status Register 2 during every interrupt or polling
cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| NCT75MNR2G | IC SENSOR TEMP DGTL 8DFN |
| NCV8881PWR2G | IC REG TRPL BUCK/LINEAR 16SOIC |
| NE1617ADS,112 | IC TEMP MONITOR 16SSOP |
| NE1619DS,118 | IC TEMP MONITOR 16SSOP |
| NIS5112D1R2G | IC ELECTRONIC FUSE HOTSWAP 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCT75DMR2G | 功能描述:板上安裝溫度傳感器 2-Channel Digital Thermometer w/ Alarm RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT75DR2G | 功能描述:板上安裝溫度傳感器 2-Channel Digital Thermometer w/ Alarm RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT75MNR2G | 功能描述:板上安裝溫度傳感器 HAS2MONOJLCC84SPACE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| NCT7717U TR | 制造商:Nuvoton Technology Corp 功能描述:SMBUS INTERFACE TEMP. SENSOR W 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
| NCT7718W TR | 制造商:Nuvoton Technology Corp 功能描述:IC SMBUS TEMP SENSOR 8MSOP |
發布緊急采購，3分鐘左右您將得到回復。