- 您現在的位置：買賣IC網 > PDF目錄385311 > GS1559-CBE2 (Gennum Corporation) GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver PDF資料下載
參數資料
| 型號： | GS1559-CBE2 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver |
| 中文描述： | GS1559的HD - LINX進程，商標第二多速率解串器與環通電纜驅動器 |
| 文件頁數： | 14/74頁 |
| 文件大?。?/td> | 686K |
| 代理商： | GS1559-CBE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
GS1559 Data Sheet
30572 - 4
July 2005
14 of 74
H8
H
Synchronous
with PCLK
Output
STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to indicate the portion of the video line containing active video data.
H signal timing is configurable via the H_CONFIG bit of the
IOPROC_DISABLE register accessible via the host interface.
Active Line Blanking (H_CONFIG = 0
h
)
The H signal will be HIGH for the entire horizontal blanking period,
including the EAV and SAV TRS words, and LOW otherwise. This is the
default setting.
TRS Based Blanking (H_CONFIG = 1
h
)
The H signal will be HIGH for the entire horizontal blanking period as
indicated by the H bit in the received TRS ID words, and LOW otherwise.
J1
CD2
Non
Synchronous
Input
STATUS SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to indicate the presence of a serial digital input signal. Normally
generated by a Gennum automatic cable equalizer.
When LOW, the serial digital input signal received at the DDI2 and DDI2
pins is considered valid.
When HIGH, the associated serial digital input signal is considered to be
invalid. In this case, the LOCKED signal is set LOW and all parallel outputs
are muted.
J5
SDO_EN/DIS
Non
Synchronous
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to enable or disable the serial digital output loop-through stage.
When set LOW, the serial digital output signals SDO and SDO are
disabled and become high impedance.
When set HIGH, the serial digital output signals SDO and SDO are
enabled.
J6
SDIN_TDI
Synchronous
with
SCLK_TCK
Input
CONTROL SIGNAL INPUT
Signal levels are LVCMOS/LVTTL compatible.
Serial Data In / Test Data Input
Host Mode (JTAG/HOST = LOW)
SDIN_TDI operates as the host interface serial input, SDIN, used to write
address and configuration information to the internal registers of the
device.
JTAG Test Mode (JTAG/HOST = HIGH)
SDIN_TDI operates as the JTAG test data input, TDI.
NOTE: If the host interface is not being used, tie this pin HIGH.
J7
V
Synchronous
with PCLK
Output
STATUS SIGNAL OUTPUT
Signal levels are LVCMOS/LVTTL compatible.
Used to indicate the portion of the video field / frame that is used for
vertical blanking.
The V signal will be HIGH for the entire vertical blanking period as
indicated by the V bit in the received TRS signals.
The V signal will be LOW for all lines outside of the vertical blanking
interval.
K1
RSET
Analog
Input
Used to set the serial digital loop-through output signal amplitude. Connect
to CD_VDD through 281
Ω
+/- 1% for 800mV
p-p
single-ended output swing.
Table 1-1: Pin Descriptions (Continued)
Pin
Number
Name
Timing
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| GS2905 | 500mA CMOS LDO Voltage Regulator |
| GS2905X15 | 500mA CMOS LDO Voltage Regulator |
| GS2905X18 | 500mA CMOS LDO Voltage Regulator |
| GS2905X25 | 500mA CMOS LDO Voltage Regulator |
| GS2905X33 | 500mA CMOS LDO Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS1560 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Voltage Controlled Oscillator |
| GS1560A | 制造商:Gennum Corporation 功能描述: |
| GS1560A_07 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Dual-Rate Deserializer |
| GS1560A_09 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Dual-Rate Deserializer |
發布緊急采購，3分鐘左右您將得到回復。