- 您現在的位置：買賣IC網 > PDF目錄385311 > GS1559-CBE2 (Gennum Corporation) GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver PDF資料下載
參數資料
| 型號： | GS1559-CBE2 |
| 廠商： | Gennum Corporation |
| 英文描述： | GS1559 HD-LINX-TM II Multi-Rate Deserializer with Loop-Through Cable Driver |
| 中文描述： | GS1559的HD - LINX進程，商標第二多速率解串器與環通電纜驅動器 |
| 文件頁數： | 28/74頁 |
| 文件大小： | 686K |
| 代理商： | GS1559-CBE2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
GS1559 Data Sheet
30572 - 4
July 2005
28 of 74
4.3.1 External VCO
The GS1559 requires the external GO1525 Voltage Controlled Oscillator as part of
the reclocker's phase-locked loop. This external VCO implementation was chosen
to ensure high quality reclocking.
Power for the external VCO is generated entirely by the GS1559 from an integrated
voltage regulator. The internal regulator uses +3.3V DC supplied via the CP_VDD
/ CP_GND pins to provide +2.5V DC on the VCO_VCC / VCO_GND pins.
The control voltage to the VCO is output from the GS1559 on the LF pin and
requires 4.7k
Ω
pull-up and pull-down resistors to ensure correct operation.
The GO1525 produces a 1.485GHz reference signal for the reclocker, input on the
VCO pin of the GS1559. Both LF and VCO signals should be referenced to the
supplied VCO_GND as shown in the recommended application circuit of
Typical
Application Circuit (Part A) on page 69
.
4.3.2 Loop Bandwidth
The loop bandwidth of the integrated reclocker is nominally 1.4MHz, but may be
increased or decreased via the LB_CONT pin. It is recommended that this pin be
connected to VCO_GND through 39.2k
Ω
to maximize the input jitter tolerance of
the device.
4.4 Serial Digital Loop-Through Output
The GS1559 contains an integrated current mode differential serial digital cable
driver with automatic slew rate control. When enabled, this serial digital output
provides an active loop-through of the input signal.
The integrated cable driver uses a separate power supply of +1.8V DC supplied via
the CD_VDD and CD_GND pins.
To enable the loop-through output, SDO_EN/DIS must be set HIGH by the
application layer. Setting the SDO_EN/DIS signal LOW will cause the SDO and
SDO output pins to become high impedance, resulting in reduced device power
consumption.
When not using the serial digital output from the GS1559, the SDO and SDO pins
should be left unconnected (floating). In addition, the SDO_EN pin should be set
LOW and the RSET pin may be AC terminated to analog ground through a 10nF
capacitor.
Gennum recommends using the GS1528A SDI Dual Slew-Rate Cable Driver to
meet SMPTE specifications.
相關PDF資料 |
PDF描述 |
|---|---|
| GS2905 | 500mA CMOS LDO Voltage Regulator |
| GS2905X15 | 500mA CMOS LDO Voltage Regulator |
| GS2905X18 | 500mA CMOS LDO Voltage Regulator |
| GS2905X25 | 500mA CMOS LDO Voltage Regulator |
| GS2905X33 | 500mA CMOS LDO Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS1560 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Voltage Controlled Oscillator |
| GS1560A | 制造商:Gennum Corporation 功能描述: |
| GS1560A_07 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:Dual-Rate Deserializer |
| GS1560A_09 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:HD-LINX II Dual-Rate Deserializer |
發布緊急采購，3分鐘左右您將得到回復。