- 您現在的位置：買賣IC網 > PDF目錄382720 > UCB1500 (NXP SEMICONDUCTORS) PCI to AC97 bridge/host controller PDF資料下載
參數資料
| 型號： | UCB1500 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | PCI to AC97 bridge/host controller |
| 中文描述： | PCI BUS CONTROLLER, PQFP80 |
| 封裝： | 12 X 12 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-315-1, LQFP-80 |
| 文件頁數： | 18/58頁 |
| 文件大小： | 1001K |
| 代理商： | UCB1500 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
Philips Semiconductors
UCB1500
PCI to AC97 bridge/host controller
Objective specification
Rev. 01 — 4 February 2000
18 of 58
9397 750 06854
Philips Electronics N.V. 2000. All rights reserved.
[82]: Power Management Capabilities (read only)
Table 22: Power Management Capabilities register bit description
Read only
Bit
Description
15-11(r)
PME support
This 5-bit field indicates the power states in which the function may assert PME.
Value is set to 00000b to indicate no PME can be asserted.
The entire setting can be overwritten by BIOS via writing to 6Ah, or an external
EEPROM. If V
AUX_AV
= 0, bit 15 shall always be zero. If V
AUX
= 1, bit 15 shall
reflect the setting of 6Ah, or that loaded from EEPROM.
10(r)
D2 support
This bit is set to ‘1’ to indicate that function supports the D2 power management
state. This setting can be overwritten by BIOS via 6Ah, or with the external
EEPROM.
9(r)
D1 support
This bit is set to ‘0’ to indicate that function does not support the D1 power
management state. This setting can be overwritten by BIOS via 6Ah, or with the
external EEPROM.
8-6(r)
Aux_Current
These bits are set to ‘0’ for PCI-PM 1.0 compliance. For PCI-PM 1.1 compliance,
these bits are overwritten by BIOS via 6Ah, or loaded from an external EEPROM
to reflect the 3.3V
AUX
current requirement.
5(r)
DSI
The Device Specific Initialization bit indicates whether special initialization of this
function is required (beyond the standard PCI configuration header) before the
generic class device driver is able to use it. This register is set to ‘0’ to indicate
that it does not require special initialization.
4(r)
Reserved.
3(r)
PME Clock
This bit is a ‘0’, indicating that the function does not rely on the presence of the
PCI clock for PME operation.
2:0(r)
Version
This register is set to 001b, indicating that this function complies with Rev 1.0 of
the PCI Power Management Interface Specification These bits can also be
overwritten by BIOS via 6Ah, or loaded from an external EEPROM to 010b for
compliance with PCI-PM 1.1.
相關PDF資料 |
PDF描述 |
|---|---|
| UCC1913D | Very low drop voltage regulators with inhibit |
| UCC1913DTR | Analog IC |
| UCC1913J | Very low drop voltage regulators with inhibit |
| UCC1913N | Very low drop voltage regulators with inhibit |
| UCC1926DS | Very low drop voltage regulators with inhibit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCB1510 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:AC97 digital modem codec |
| UCB15-101T-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ultra Current Beads |
| UCB1510DB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:AC97 digital modem codec |
| UCB15-121T-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ultra Current Beads |
| UCB15-600T-RC | 制造商:ALLIED 制造商全稱:Allied Components International 功能描述:Ultra Current Beads |
發布緊急采購，3分鐘左右您將得到回復。