- 您現在的位置：買賣IC網 > PDF目錄106304 > 11274-502-XTD PLL FREQUENCY SYNTHESIZER, 28 MHz, PDSO16 PDF資料下載
參數資料
| 型號： | 11274-502-XTD |
| 元件分類： | PLL合成/DDS/VCOs |
| 英文描述： | PLL FREQUENCY SYNTHESIZER, 28 MHz, PDSO16 |
| 封裝： | 0.150 INCH, GREEN, SOIC-16 |
| 文件頁數： | 3/40頁 |
| 文件大小： | 746K |
| 代理商： | 11274-502-XTD |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
11
AMI Semiconductor - Rev. 2.0, Jun. 05
www.amis.com
FS6131-01/FS6131-01g Programmable Line Lock Clock Generator IC
Data Sheet
0.0
5 .0
10.0
15 .0
20 .0
25 .0
0
2 0
40
60
80
CLKP/CLKN PECL Output Current (m A)
IPRG
Input
Current
(mA)
Figure 12: IPRG to CLKP/CLKN Current
5.0 I2C-bus Control Interface
This device is a read/write slave device meeting all Philips I
2C-bus specifications except a "general call." The bus has to be controlled
by a master device that generates the serial clock SCL, controls bus access and generates the START and STOP conditions while
the device works as a slave. Both master and slave can operate as a transmitter or receiver, but the master device determines which
mode is activated. A device that sends data onto the bus is defined as the transmitter, and a device receiving data as the receiver.
I
2C-bus logic levels noted herein are based on a percentage of the power supply (VDD). A logic-one corresponds to a nominal voltage of VDD, while
a logic-zero corresponds to ground (VSS).
5.1 Bus Conditions
Data transfer on the bus can only be initiated when the bus is not busy. During the data transfer, the data line (SDA) must remain stable whenever
the clock line (SCL) is high. Changes in the data line while the clock line is high will be interpreted by the device as a START or STOP condition.
The following bus conditions are defined by the I
2C-bus protocol.
5.1.1 Not Busy
Both the data (SDA) and clock (SCL) lines remain high to indicate the bus is not busy.
5.1.2 START Data Transfer
A high to low transition of the SDA line while the SCL in-put is high indicates a START condition. All commands to the device must be preceded
by a START condition.
5.1.3 STOP Data Transfer
A low to high transition of the SDA line while SCL is held high indicates a STOP condition. All commands to the device must be followed by a
STOP condition.
5.1.4 Data Valid
The state of the SDA line represents valid data if the SDA line is stable for the duration of the high period of the SCL line after a START condition
occurs. The data on the SDA line must be changed only during the low period of the SCL signal. There is one clock pulse per data bit.
相關PDF資料 |
PDF描述 |
|---|---|
| 15MV500 | 1-OUTPUT 1.25 W DC-DC UNREG PWR SUPPLY MODULE |
| 1025PE-42TE13 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 1021ZD4E-28TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, DSO8 |
| 1025LI-45TE13 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8 |
| 12IWR1-05-05-NT | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1127-45-0516 | 制造商:Concord Electronics Inc 功能描述:Insulated Terminal 29.3mm 6.35mm Electro-Solder Over Copper |
| 1-1274574-0 | 制造商:TE Connectivity 功能描述:COMM BNC PLUG, LEAD FREE - Bulk |
| 112746 | 制造商:Amphenol Connex 功能描述: |
| 1127470000 | 功能描述:TOS 230VUC 230VAC1A 制造商:weidmuller 系列:* 零件狀態:有效 標準包裝:1 |
| 112747-HMC603MS10E | 制造商:Hittite Microwave Corp 功能描述:BOARD EVAL HMC603MS10E |
發布緊急采購，3分鐘左右您將得到回復。