- 您現在的位置：買賣IC網 > PDF目錄373970 > AD9910 (Analog Devices, Inc.) 1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer PDF資料下載
參數資料
| 型號： | AD9910 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | XO, clock |
| 英文描述： | 1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer |
| 中文描述： | 1 GSPS的，14位，3.3伏的CMOS直接數字頻率合成 |
| 文件頁數： | 55/60頁 |
| 文件大小： | 764K |
| 代理商： | AD9910 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁當前第55頁第56頁第57頁第58頁第59頁第60頁
AD9910
Control Function Register 2 (CFR2)
Address 0x01; 4 bytes are assigned to this register.
Rev. 0 | Page 55 of 60
Table 18. Bit Descriptions for CFR2
Bit(s)
Descriptor
31:26
Not Available
25
DROVER Pin Active
24
23
Internal I/O Update Active
Explanation
Ineffective unless Bit 19 = 1. Refer to DROVER Pin section for details.
Ineffective if Bit 19 = 1 or CFR1<31> = 1 or CFR1<9> = 1.
0 = the amplitude scaler is bypassed and shut down for power conservation (default).
1 = the amplitude is scaled by the ASF from the active profile.
This bit is effective without the need for an I/O update.
0 = serial I/O programming is synchronized with the external assertion of the
I/O_UPDATE pin, which is configured as an input pin (default).
1 = serial I/O programming is synchronized with an internally generated I/O update
signal (the internally generated signal appears at the I/O_UPDATE pin, which is
configured as an output pin).
Enable Amplitude Scale
from Single Tone Profiles
22
SYNC_CLK Enable
0 = The SYNC_CLK pin is disabled; static Logic 0 output.
1 = the SYNC_CLK pin generates a clock signal at f
SYSCLK
; used for synchronization of the
serial I/O port (default).
See Table 11 for details. Default is 00
2
. See Digital Ramp Generator (DRG) section for details.
0 = disables digital ramp generator functionality (default).
1 = enables digital ramp generator functionality.
See Digital Ramp Generator (DRG) section for details.
0 = disables no-dwell high functionality (default).
1 = enables no-dwell high functionality.
See Digital Ramp Generator (DRG) section for details.
0 = disables no-dwell low functionality (default).
1 = enables no-dwell low functionality.
0 = a serial I/O port read operation of the FTW register reports the contents of the FTW
register (default).
1 = a serial I/O port read operation of the FTW register reports the actual 32-bit word
appearing at the input to the DDS phase accumulator.
Ineffective unless Bit 23 = 1. Sets the prescale ratio of the divider that clocks the auto I/O
update timer as follows:
00 = divide-by-1 (default).
01 = divide-by-2.
10 = divide-by-4.
11 = divide-by-8.
0 = the PDCLK pin is disabled and forced to a static Logic 0 state; the internal clock signal
continues to operate and provide timing to the data assembler.
1 = the internal PDCLK signal appears at the PDCLK pin (default).
0 = normal PDCLK polarity; Q-data associated with Logic 1, I-data with Logic 0 (default).
1 = inverted PDCLK polarity.
0 = no inversion.
1 = inversion.
0 = simultaneous application of amplitude, phase, and frequency changes to the DDS
arrive at the output in the order listed (default).
1 = simultaneous application of amplitude, phase, and frequency changes to the DDS
arrive at the output simultaneously.
21:20
19
18
17
16
Digital Ramp Destination
Digital Ramp Enable
Digital Ramp No-Dwell High
Digital Ramp No-Dwell Low
Read Effective FTW
15:14
I/O Update Rate Control
13:12
11
Not Available
PDCLK Enable
10
9
8
7
PDCLK Invert
TxEnable Invert
Not Available
Matched Latency Enable
相關PDF資料 |
PDF描述 |
|---|---|
| AD9910_07 | 1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer |
| AD9910BSVZ | 1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer |
| AD9910BSVZ-REEL | 1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer |
| AD9912 | 1 GSPS Direct Digital Synthesizer w/ 14-bit DAC |
| AD9913 | Low Power 250 MSPS 10-Bit DAC 1.8 V CMOS Direct Digital Synthesizer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9910/PCBZ | 功能描述:數據轉換 IC 開發工具 1GSPS 14 bit DDS w/ parallel input port RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| AD9910_07 | 制造商:AD 制造商全稱:Analog Devices 功能描述:1 GSPS, 14-Bit, 3.3 V CMOS Direct Digital Synthesizer |
| AD9910BSVZ | 功能描述:IC DDS 1GSPS 14BIT PAR 100TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| AD9910BSVZ | 制造商:Analog Devices 功能描述:IC DDS 1GHZ TQFP-100 制造商:Analog Devices 功能描述:IC, DDS, 1GHZ, TQFP-100 |
| AD9910BSVZ-REEL | 功能描述:IC DDS 1GSPS 14BIT PAR 100TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 直接數字合成 (DDS) 系列:- 產品變化通告:Product Discontinuance 27/Oct/2011 標準包裝:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 調節字寬（位）:32 b 電源電壓:2.97 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。