- 您現在的位置：買賣IC網 > PDF目錄382369 > P90CL301 (NXP Semiconductors N.V.) Low voltage 16-bit microcontroller PDF資料下載
參數資料
| 型號： | P90CL301 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Low voltage 16-bit microcontroller |
| 中文描述： | 低電壓16位微控制器 |
| 文件頁數： | 56/92頁 |
| 文件大小： | 526K |
| 代理商： | P90CL301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
1996 Dec 11
56
Philips Semiconductors
Preliminary specification
Low voltage 16-bit microcontroller
P90CL301BFH (C100)
15 ON-BOARD TEST CONCEPT
To improve the on-board debugging two functions are
implemented, the ON-Circuit Emulation (ONCE) mode and
the on-chip Test-ROM.
15.1
ONCE mode
The ON-Circuit Emulation (ONCE) mode eases the testing
of an application without having to remove the controller
from the board. The ONCE mode is entered by pulling
CSBT LOW during reset. In this mode the address bus,
data bus and bus control signals are in 3-state mode, all
other output or bidirectional pins are weakly pulled HIGH.
In this mode an emulator probe can be hooked-up to the
circuit. Normal operation is restored with a normal reset.
15.2
Test-ROM
A second on-board debugging function is introduced for
the situation where no extra connector can be placed on
the PCB. It consists of an internal Test-ROM of 256 bytes
which is used as boot ROM after a special test mode is
activated during reset. The CPU will execute the code
placed in the Test-ROM and initialize the UART0 and its
baud rate generator and wait for commands to be sent to
UART0.
The internal access time is in this case 3 cycles long. It can
only be accessed in supervisor mode.
The purpose of the Test-ROM is to offer the user a simple
software interface to load programs for testing its own
application and to transmit back the test result.
The program can be loaded from the host into either the
on-chip RAM or the external memory. The Test-ROM
mode is entered by pulling LOW the R/W / TROM pin
during reset.
Just after the RESET initialization, the user should send a
character of 9 bits (one stop bit plus eight data bits) with all
bits being zero, on the RX0 line.
Using the timer, the character length is captured and then
the baud rate is automatically calculated and the baud rate
generator is initialized. The UART0 is then initialized in
Mode 3 with SM2 multiprocessor bit set, REN and TB8 bit
set (SCON = F8H). The hardware is now ready to handle
the protocol using the following 4 commands
(Code 00 to 11).
Table 89
Command format
Table 90
Command description
7
6
5
4
3
2
1
0
Code
NB byte
1
BIT
SYMBOL
DESCRIPTION
7, 6
5 to 0
Code
Pointer commands; see Table 91.
Indicates the length of the transfer; e.g. (NB byte
1) = 0 means a 1 byte transfer,
(NB byte
1) = 63 means a 64 byte transfer.
NB byte
1
相關PDF資料 |
PDF描述 |
|---|---|
| P90CL301BFH | Low voltage 16-bit microcontroller |
| P93U422-35DC | x4 SRAM |
| P93U422-35DM | x4 SRAM |
| P93U422-35DMB | x4 SRAM |
| P93U422-35LC | x4 SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P90CL301BFH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low voltage 16-bit microcontroller |
| P-90-F | 制造商:Hozan Tool Industrial Co Ltd 功能描述: |
| P90PCT101PC | 制造商:PERFORMANCE/ 功能描述:90PCT101PC |
| P-910 | 制造商:Hozan Tool Industrial Co Ltd 功能描述: |
| P9-100001 | 制造商:OTTO Engineering Inc 功能描述:P9-111122 EX H20 |
發布緊急采購，3分鐘左右您將得到回復。