欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32FU8
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 16-Bit Microcontroller
中文描述: 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 13/128頁
文件大?。?/td> 748K
代理商: MC68B912B32FU8
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
13
3.3.8 External Address and Data Buses (ADDR[15:0] and DATA[15:0])
External bus pins share function with general-purpose I/O ports A and B. In single-chip operating
modes, the pins can be used for I/O; in expanded modes, the pins are used for the external buses.
In expanded wide mode, ports A and B are used for multiplexed 16-bit data and address buses. PA[7:0]
correspond to ADDR[15:8]/DATA[15:8]; PB[7:0] correspond to ADDR[7:0]/DATA[7:0].
In expanded narrow mode, ports A and B are used for the 16-bit address bus, and an 8-bit data bus is
multiplexed with the most significant half of the address bus on port A. In this mode, 16-bit data is han-
dled as two back-to-back bus cycles, one for the high byte followed by one for the low byte. PA[7:0]
correspond to ADDR[15:8] and to DATA[15:8] or DATA[7:0], depending on the bus cycle. The state of
the address pin should be latched at the rising edge of E. To allow for maximum address setup time at
external devices, a transparent latch should be used.
3.3.9 Read/Write (R/W)
In all modes this pin can be used as I/O and is a general-purpose input with an active pull-up out of
reset. If the read/write function is required it should be enabled by setting the RDWE bit in the PEAR
register. External writes will not be possible until enabled.
3.3.10 Low-Byte Strobe (LSTRB)
In all modes this pin can be used as I/O and is a general-purpose input with an active pull-up out of
reset. If the strobe function is required, it should be enabled by setting the LSTRE bit in the PEAR reg-
ister. This signal is used in write operations and so external low byte writes will not be possible until this
function is enabled. This pin is also used as TAGLO in special expanded modes and is multiplexed with
the LSTRB function.
3.3.11 Instruction Queue Tracking Signals (IPIPE1 and IPIPE0)
These signals are used to track the state of the internal instruction execution queue. Execution state is
time-multiplexed on the two signals. Refer to
16 Development Support
.
3.3.12 Data Bus Enable (DBE)
The DBE pin (PE7) is an active low signal that will be asserted low during E-clock high time. DBE pro-
vides separation between output of a multiplexed address and the input of data. When an external ad-
dress is stretched, DBE is asserted during what would be the last quarter cycle of the last E-clock cycle
of stretch. In expanded modes this pin is used to enable the drive control of external buses during ex-
ternal reads. Use of the DBE is controlled by the NDBE bit in the PEAR register. DBE is enabled out of
reset in expanded modes. This pin has an active pull-up during and after reset in single-chip modes.
相關PDF資料
PDF描述
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
MC68EN360CFE25 QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
MC68C912B32CFU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
主站蜘蛛池模板: 中牟县| 巴林左旗| 辉县市| 闽清县| 若羌县| 勃利县| 荔浦县| 普洱| 澄江县| 疏勒县| 昭苏县| 恩施市| 廊坊市| 南和县| 红原县| 洞头县| 隆林| 杭州市| 盐源县| 游戏| 兴山县| 乃东县| 闻喜县| 松溪县| 忻城县| 宜兰市| 大同县| 赣州市| 苍溪县| 泾阳县| 南郑县| 鄂温| 柳河县| 都安| 扶沟县| 高安市| 中卫市| 西昌市| 全南县| 刚察县| 翁源县|