- 您現在的位置：買賣IC網 > PDF目錄371046 > MC68B912B32FU8 (MOTOROLA INC) 16-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68B912B32FU8 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 94/128頁 |
| 文件大小： | 748K |
| 代理商： | MC68B912B32FU8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁當前第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
MOTOROLA
94
MC68HC912B32
MC68HC912B32TS/D
Read or write anytime.
SPIE — SPI Interrupt Enable
1 = Hardware interrupt sequence is requested each time the SPIF or MODF status flag is set
0 = SPI interrupts are inhibited
SPE — SPI System Enable
0 = SPI internal hardware is initialized and SPI system is in a low-power disabled state.
1 = PS[4:7] are dedicated to the SPI function
When MODF is set, SPE always reads zero. SP0CR1 must be written as part of a mode fault recovery
sequence.
SWOM — Port S Wired-OR Mode
Controls not only SPI output pins but also the general-purpose output pins (PS[4:7]) which are not used
by SPI.
0 = SPI and/or PS[4:7] output buffers operate normally
1 = SPI and/or PS[4:7] output buffers behave as open-drain outputs
MSTR — SPI Master/Slave Mode Select
0 = Slave mode
1 = Master mode
CPOL, CPHA — SPI Clock Polarity, Clock Phase
These two bits are used to specify the clock format to be used in SPI operations. When the clock polarity
bit is cleared and data is not being transferred, the SCK pin of the master device is low. When CPOL is
set, SCK idles high. See
Figure 22
and
Figure 23
.
SSOE — Slave Select Output Enable
The SS output feature is enabled only in the master mode by asserting the SSOE and DDS7.
LSBF — SPI LSB First Enable
0 = Data is transferred most significant bit first
1 = Data is transferred least significant bit first
Normally data is transferred most significant bit first. This bit does not affect the position of the MSB and
LSB in the data register. Reads and writes of the data register will always have MSB in bit 7.
Read or write anytime.
SSWAI — SSI Stop in Wait Mode
0 = SSI clock operate normally
1 = Halt SSI clock generation when in wait mode
SPC0 — Serial Pin Control 0
This bit decides serial pin configurations with MSTR control bit.
SP0CR2
— SPI Control Register 2
$00D1
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
SSWAI
SPC0
RESET:
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68C912B32CFU8 | 16-Bit Microcontroller |
| MC68CK338 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| MC68EC060 | 32-Bit Microprocessors.(32位微處理器) |
| MC68EN360RC25V | QUad Integrated Communications Controller Users Manual |
| MC68EN360CFE25 | QUad Integrated Communications Controller Users Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68BOOL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOP | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOS | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68C812A4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics |
| MC68C912B32CFU8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。