- 您現在的位置：買賣IC網 > PDF目錄371046 > MC68B912B32FU8 (MOTOROLA INC) 16-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68B912B32FU8 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 88/128頁 |
| 文件大小： | 748K |
| 代理商： | MC68B912B32FU8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
MOTOROLA
88
MC68HC912B32
MC68HC912B32TS/D
RWU — Receiver Wake-Up Control
0 = Normal SCI Receiver
1 = Enables the wake-up function and inhibits further receiver interrupts. Normally hardware wakes
the receiver by automatically clearing this bit.
SBK — Send Break
0 = Break generator off
1 = Generate a break code (at least 10 or 11 contiguous zeros)
As long as SBK remains set the transmitter will send zeros. When SBK is changed to zero, the current
frame of all zeros is finished before the TxD line goes to the idle state. If SBK is toggled on and off, the
transmitter will send 10 (or 11) zeros and then revert to mark idle or sending data.
The bits in these registers are set by various conditions in the SCI hardware and are automatically
cleared by special acknowledge sequences. The receive related flag bits in SC0SR1 (RDRF, IDLE, OR,
NF, FE, and PF) are all cleared by a read of the SC0SR1 register followed by a read of the transmit/
receive data register L. However, only those bits which were set when SC0SR1 was read will be cleared
by the subsequent read of the transmit/receive data register L. The transmit related bits in SC0SR1
(TDRE and TC) are cleared by a read of the SC0SR1 register followed by a write to the transmit/receive
data register L.
Read anytime (used in auto clearing mechanism). Write has no meaning or effect.
TDRE — Transmit Data Register Empty Flag
New data will not be transmitted unless SC0SR1 is read before writing to the transmit data register. Re-
set sets this bit.
0 = SC0DR busy
1 = Any byte in the transmit data register is transferred to the serial shift register so new data may
now be written to the transmit data register.
TC — Transmit Complete Flag
Flag is set when the transmitter is idle (no data, preamble, or break transmission in progress). Clear by
reading SC0SR1 with TC set and then writing to SC0DR.
0 = Transmitter busy
1 = Transmitter is idle
RDRF — Receive Data Register Full Flag
Once cleared, IDLE is not set again until the RxD line has been active and becomes idle again. RDRF
is set if a received character is ready to be read from SC0DR. Clear the RDRF flag by reading SC0SR1
with RDRF set and then reading SC0DR.
0 = SC0DR empty
1 = SC0DR full
IDLE — Idle Line Detected Flag
Receiver idle line is detected (the receipt of a minimum of 10/11 consecutive ones). This bit will not be
set by the idle line condition when the RWU bit is set. Once cleared, IDLE will not be set again until after
RDRF has been set (after the line has been active and becomes idle again).
0 = RxD line is idle
1 = RxD line is active
OR — Overrun Error Flag
New byte is ready to be transferred from the receive shift register to the receive data register and the
receive data register is already full (RDRF bit is set). Data transfer is inhibited until this bit is cleared.
0 = No overrun
1 = Overrun detected
SC0SR1
— SCI Status Register 1
$00C4
Bit 7
6
5
4
3
2
1
Bit 0
TDRE
TC
RDRF
IDLE
OR
NF
FE
PF
RESET:
1
1
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68C912B32CFU8 | 16-Bit Microcontroller |
| MC68CK338 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| MC68EC060 | 32-Bit Microprocessors.(32位微處理器) |
| MC68EN360RC25V | QUad Integrated Communications Controller Users Manual |
| MC68EN360CFE25 | QUad Integrated Communications Controller Users Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68BOOL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOP | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOS | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68C812A4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics |
| MC68C912B32CFU8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。