欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32FU8
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 16-Bit Microcontroller
中文描述: 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80
封裝: QFP-80
文件頁數: 15/128頁
文件大小: 748K
代理商: MC68B912B32FU8
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
15
3.4 Port Signals
The MC68HC912B32 incorporates eight ports which are used to control and access the various device
subsystems. When not used for these purposes, port pins may be used for general-purpose I/O. In ad-
dition to the pins described below, each port consists of a data register which can be read and written
at any time, and, with the exception of port AD and PE[1:0], a data direction register which controls the
direction of each pin. After reset all port pins are configured as input.
3.4.1 Port A
Port A pins are used for address and data in expanded modes. The port data register is not in the ad-
dress map during expanded and peripheral mode operation. When it is in the map, port A can be read
or written at anytime.
Register DDRA determines whether each port A pin is an input or output. DDRA is not in the address
map during expanded and peripheral mode operation. Setting a bit in DDRA makes the corresponding
bit in port A an output; clearing a bit in DDRA makes the corresponding bit in port A an input. The default
reset state of DDRA is all zeros.
When the PUPA bit in the PUCR register is set, all port A input pins are pulled up internally by an active
pull-up device. This bit has no effect if the port is being used in expanded modes as the pull-ups are
inactive.
Setting the RDPA bit in register RDRIV causes all port A outputs to have reduced drive level. RDRIV
can be written once after reset. RDRIV is not in the address map in peripheral mode. Refer to
6 Bus
Control and Input/Output
.
3.4.2 Port B
Port B pins are used for address and data in expanded modes. The port data register is not in the ad-
dress map during expanded and peripheral mode operation. When it is in the map, port B can be read
or written at anytime.
Register DDRB determines whether each port B pin is an input or output. DDRB is not in the address
map during expanded and peripheral mode operation. Setting a bit in DDRB makes the corresponding
bit in port B an output; clearing a bit in DDRB makes the corresponding bit in port B an input. The default
reset state of DDRB is all zeros.
When the PUPB bit in the PUCR register is set, all port B input pins are pulled up internally by an active
pull-up device. This bit has no effect if the port is being used in expanded modes as the pull-ups are
inactive.
Setting the RDPB bit in register RDRIV causes all port B outputs to have reduced drive level. RDRIV
can be written once after reset. RDRIV is not in the address map in peripheral mode. Refer to
6 Bus
Control and Input/Output
.
3.4.3 Port E
Port E pins operate differently from port A and B pins. Port E pins are used for bus control signals and
interrupt service request signals. When a pin is not used for one of these specific functions, it can be
used as general-purpose I/O. However, two of the pins (PE[1:0]) can only be used for input, and the
states of these pins can be read in the port data register even when they are used for IRQ and XIRQ.
The PEAR register determines pin function, and register DDRE determines whether each pin is an input
or output when it is used for general-purpose I/O. PEAR settings override DDRE settings. Because
PE[1:0] are input-only pins, only DDRE[7:2] have effect. Setting a bit in the DDRE register makes the
corresponding bit in port E an output; clearing a bit in the DDRE register makes the corresponding bit
in port E an input. The default reset state of DDRE is all zeros.
相關PDF資料
PDF描述
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
MC68EN360CFE25 QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
MC68C912B32CFU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
主站蜘蛛池模板: 永宁县| 玛多县| 齐齐哈尔市| 东乡县| 喀什市| 裕民县| 香港| 哈巴河县| 岑溪市| 当涂县| 佛学| 江津市| 上高县| 色达县| 黄山市| 五莲县| 定襄县| 漯河市| 托克托县| 岑巩县| 孝义市| 定南县| 克拉玛依市| 响水县| 喜德县| 康乐县| 福海县| 镇原县| 高雄市| 资兴市| 惠东县| 衡阳市| 渝中区| 吴堡县| 湟中县| 贺州市| 苍山县| 车致| 庆安县| 岗巴县| 云梦县|