- 您現在的位置：買賣IC網 > PDF目錄367493 > L84225 L84225 100BaseTX/FX/10BaseT Physical Layer Device technical manual 4/02 PDF資料下載
參數資料
| 型號： | L84225 |
| 英文描述： | L84225 100BaseTX/FX/10BaseT Physical Layer Device technical manual 4/02 |
| 中文描述： | L84225 100BaseTX/FX/10BaseT物理層設備的技術手冊，4月2日 |
| 文件頁數： | 47/118頁 |
| 文件大小： | 890K |
| 代理商： | L84225 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
Functional Description
Copyright 1999-2002 by LSI Logic Corporation. All rights reserved.
47 of 118
April, 2002
The internal CRS loopback can be disabled by setting the TXEN to CRS
loopback disable bit in the MI serial port Channel Configuration register.
When this bit is set, TXEN is no longer looped back to CRS.
2.19.2 Diagnostic Loopback
A diagnostic loopback mode can also be selected by setting the loopback
bit in the MI serial port Control register. When diagnostic loopback is
enabled, TXD[3:0] data is looped back onto RXD[3:0], TXEN is looped
back onto CRS, RXDV operates normally, the TP receive and transmit
paths are disabled, the transmit link pulses are halted, and the Half/Full
Duplex modes do not change. Diagnostic loopback mode can not be
enabled when the FBI interface is selected.
2.20 Reset
The L84225 is reset when either:
1.
VDD is applied to the device,
2.
the reset bit is set in the MI serial port Control register, or
3.
the RESET pin is asserted active low.
When the reset is initiated by either (1) or (2), an internal power-on reset
pulse is generated which resets all internal circuits, forces the MI serial
port bits to their default values, and latches in new values for the MI
address. After the power-on reset pulse has finished, the reset bit in the
MI serial port Control register is cleared and the device is ready for
normal operation. The device is guaranteed to be ready for normal
operation 50 ms after the reset was initiated.
When the reset is initiated by (3), the identical procedure takes place as
in (1) and (2), except the device stays in reset until the RESET pin is
deasserted high.
2.21 Powerdown
The L84225 can be powered down by setting the powerdown bit in the
MI serial port Control register. In powerdown mode, the TP outputs are
in high impedance state, all functions are disabled except the MI serial
port, and the power consumption is reduced to a minimum. The device
will be ready for normal operation 50 ms after powerdown is deasserted.
相關PDF資料 |
PDF描述 |
|---|---|
| L84302 | L84302 Quad 100/10 Mbps 4-Port Ethernet Controller with RMON/SNMP Management Counters technical manual 4/02 |
| L8560 | Low-Power SLIC with Ringing |
| L8567 | SLIC for Peoples Republic of China Applications |
| L8567-32PLCC | Telecommunication IC |
| L8567-44PLCC | Telecommunication IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L84225/B1 | 制造商:LSI Corporation 功能描述: |
| L8446-04 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-06 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-07 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-41 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
發布緊急采購，3分鐘左右您將得到回復。