- 您現在的位置：買賣IC網 > PDF目錄367493 > L84225 L84225 100BaseTX/FX/10BaseT Physical Layer Device technical manual 4/02 PDF資料下載
參數資料
| 型號： | L84225 |
| 英文描述： | L84225 100BaseTX/FX/10BaseT Physical Layer Device technical manual 4/02 |
| 中文描述： | L84225 100BaseTX/FX/10BaseT物理層設備的技術手冊，4月2日 |
| 文件頁數： | 78/118頁 |
| 文件大小： | 890K |
| 代理商： | L84225 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁
78 of 118
April, 2002
L84225 Quad 100BaseTX/FX/10BaseT Phys. Layer Device - Technical Manual
Copyright 1999-2002 by LSI Logic Corporation. All rights reserved.
fiber interface is disabled (and the TP interface enabled) by connecting
the SD_[3:0]/FXEN_[3:0] pins to GND for that channel.
AutoNegotiation and the scrambler/descrambler are disabled when the
fiber interface is enabled.
The voltage applied to the SD_THR pin sets the input reference level of
the fiber interface for the single ended Signal Detect inputs only. If a 3.3
V fiber transceiver is used with the L84225, this pin should be tied to
GND. If a 5 V fiber transceiver is used, this pin needs to be tied to
VCC(3.3V)-1.3 V (about 2V), but referenced to the 5V supply of the fiber
transceiver. An easy way to do this is with a 15K:10K voltage divider from
the 5 V supply to ground, with the center point of the divider connected
to SD_THR, as shown in
Figure 14
.
4.5.2 Operation with 3.3V Fiber Transceivers
Termination on the differential outputs of the fiber transceiver module
must be observed for proper impedance matching, which is normally the
equivalent of 50 Ohms single ended. The terminating resistor values are
shown in
Figure 13
for FXOP/FXON (outputs), FXIP/ FXIN (inputs) and
SD_[3:0]/FXEN_[3:0] (inputs) for use with 3.3V fiber modules. The
calculated termination resistors on FXOP/FXON are a pull-up of 69.8
Ohms to 3.3V and a pulldown of 174 Ohms to ground.
The termination network at the fiber inputs (FXIP/FXIN and
SD_[3:0]/FXEN_[3:0]) of the L84225 is specified by the fiber module
manufacturer and will normally be a pull-up of 127 Ohms to 3.3V and a
pulldown of 82.5 Ohms to GND, as shown in
Figure 13
. Note that the
Input and Output termination resistor values are different since the output
driver of the Fiber module and the L84225 have a different structure. The
interface network for 3.3V fiber transceiver modules is shown in
Figure 13
.
相關PDF資料 |
PDF描述 |
|---|---|
| L84302 | L84302 Quad 100/10 Mbps 4-Port Ethernet Controller with RMON/SNMP Management Counters technical manual 4/02 |
| L8560 | Low-Power SLIC with Ringing |
| L8567 | SLIC for Peoples Republic of China Applications |
| L8567-32PLCC | Telecommunication IC |
| L8567-44PLCC | Telecommunication IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L84225/B1 | 制造商:LSI Corporation 功能描述: |
| L8446-04 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-06 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-07 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
| L8446-41 | 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES |
發布緊急采購，3分鐘左右您將得到回復。