欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： ADUC845
廠商： Analog Devices, Inc.
元件分類： ADC
英文描述： MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
中文描述： MicroConverter的多通道ADC的24-/16-Bit與嵌入式62 kB閃存以及單周期控制器
文件頁數： 32/108頁
文件大小： 1109K
代理商： ADUC845
ADuC845/ADuC847/ADuC848
AUXILIARY ADC (ADUC845 ONLY)
Table 18. ADuC845 Typical Output RMS Noise (μV) vs.
Update Rate with Chop Enabled
SF Word
Data Update Rate (Hz)
13
105.03
23
59.36
27
50.56
69
19.79
255
5.35
Rev. A | Page 32 of 108
μV
17.46
3.13
4.56
2.66
1.13
Table 19. ADuC845 Typical Peak-to-Peak Resolution (Bits) vs.
Update Rate
1
with Chop Enabled
SF Word
Data Update Rate (Hz)
13
105.03
23
59.36
27
50.56
69
19.79
255
5.35
Bits
15.5
18
17.5
18
19.5
1
ADC converting in bipolar mode.
Table 20. ADuC845 Typical Output RMS Noise (μV) vs.
Update Rate with Chop Disabled
SF Word
Data Update Rate (Hz)
3
1365.33
13
315.08
66
62.06
69
59.36
81
50.57
255
16.06
μV
1386.58
34.94
3.2
3.19
3.14
1.71
Table 21. ADuC845 Peak-to-Peak Resolution (Bits) vs.
Update Rate with Chop Disabled
SF Word
Data Update Rate (Hz)
3
1365.33
13
315.08
66
62.06
69
59.36
81
50.57
255
16.06
REFERENCE INPUTS
The ADuC845/ADuC847/ADuC848 each have two separate
differential reference inputs, REFIN± and REFIN2±. While both
references are available for use with the primary ADC, only
REFIN± is available for the auxiliary ADC (ADuC845 only).
The common-mode range for these differential references is
from AGND to AV
DD
. The nominal external reference voltage is
2.5 V, with the primary and auxiliary (ADuC845 only)
reference
select bits configured from the ADC0CON2 and ADC1CON
(ADuC845 only), respectively.
Bits
9
14.5
18
18
18
19
When an external reference voltage is used, the primary ADC
sees this internally as a 2.56 V reference (V
REF
× 1.024).
Therefore, any calculations of LSB size should account for this.
For instance, with a 2.5 V external reference connected and
using a gain of 1 on a unipolar range (2.56 V), the LSB size is
(2.56/2
24
) = 152.6 nV (if using the 24-bit ADC on the ADuC845
or ADuC847). If a bipolar gain of 4 is used (±640 mV), the LSB
size is (±640 mV)/2
24
) = 76.3 nV (again using the 24-bit ADC
on the ADuC845 or ADuC847).
The ADuC845/ADuC847/ADuC848 can also be configured to
use the on-chip band gap reference via the XREF0/1 bits in the
ADC0CON2 SFR (for primary ADC) or the AXREF bit in
ADC1CON (for auxiliary ADC (ADuC845 only)). In this mode
of operation, the ADC sees the internal reference of 1.25 V,
thereby halving all the input ranges. A consequence of using the
internal band gap reference is a noticeable degradation in peak-
to-peak resolution. For this reason, operation with an external
reference is recommended.
In applications where the excitation (voltage or current) for the
transducer on the analog input also drives the reference inputs
for the part, the effect of any low frequency noise in the
excitation source is removed because the application is ratio-
metric. If the parts are not used in a ratiometric configuration, a
low noise reference should be used. Recommended reference
voltage sources for the ADuC845/ADuC847/ADuC848 include
ADR421, REF43, and REF192.
The reference inputs provide a high impedance, dynamic load
to external connections. Because the impedance of each reference
input is dynamic, resistor/capacitor combinations on these pins
can cause dc gain errors, depending on the output impedance of
the source that is driving the reference inputs. Reference voltage
sources, such as those mentioned above, for example, the ADR421,
typically have low output impedances, and, therefore, decoupling
capacitors on the REFIN± or REFIN2± inputs would be recom-
mended (typically 0.1 μF). Deriving the reference voltage from
an external resistor configuration means that the reference input
sees a significant external source impedance. External decoupling
of the REFIN± and/or REFIN2± inputs is not recommended in
this type of configuration.
BURNOUT CURRENT SOURCES
The primary ADC on the ADuC845 and the ADC on the
ADuC847 and ADuC848 incorporate two 200 μA constant
current generators, one sourcing current from the AV
DD
to
AIN(+), and one sinking current from AIN(
) to AGND. These
currents are only configurable for use on AIN4 to AIN5 and/or
AIN6 to AIN7 in differential mode only, from the ICON.6 bit in
the ICON SFR (see Table 30). These burnout current sources are
also available only with buffering enabled via the BUF0/BUF1 bits
in the ADC0CON1 SFR. Once the burnout currents are turned
on, a current flows in the external transducer circuit, and a
measurement of the input voltage on the analog input channel
相關PDF資料
PDF描述
ADUC845BCP8-3 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC847BCP8-3 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC845BCP8-5 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC847BCP8-5 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC845BCP62-3 MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
相關代理商/技術參數
參數描述
ADUC845_12 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter?? Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADUC845BCP32-3 制造商:Analog Devices 功能描述:10 CHANNEL 24 BIT DUAL ADC + FAST 8BIT UP - Trays
ADUC845BCP32-5 制造商:Analog Devices 功能描述:10 CHANNEL 24 BIT DUAL ADC + FAST 8BIT UP - Trays
ADUC845BCP62-3 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 56-Pin LFCSP EP
ADUC845BCP62-5 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 辽阳县| 许昌市| 涪陵区| 清流县| 朝阳县| 永城市| 禹州市| 晋中市| 蓝田县| 思南县| 邹城市| 邓州市| 舒兰市| 甘泉县| 广汉市| 徐汇区| 景泰县| 东山县| 平定县| 日照市| 玉田县| 南投县| 溧阳市| 奉新县| 金昌市| 海原县| 滦平县| 郑州市| 凤凰县| 京山县| 济阳县| 阿拉善右旗| 荔浦县| 西安市| 庆云县| 东兰县| 固阳县| 任丘市| 蒙阴县| 汽车| 万盛区|