欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: L84302
元件分類: 通用總線功能
英文描述: L84302 Quad 100/10 Mbps 4-Port Ethernet Controller with RMON/SNMP Management Counters technical manual 4/02
中文描述: L84302四100/10 Mbps的4端口以太網的遠程監控控制器/ SNMP管理處的技術手冊,4月2日
文件頁數: 65/128頁
文件大小: 997K
代理商: L84302
Functional Description
Copyright 1997-2002 by LSI Logic Corporation. All rights reserved.
65 of 128
April, 2002
mean both transmitted and received information because Ethernet
was originally a shared media protocol. As such, transmit packet and
octet counters are also available in counters #17-26 and can be
summed with the receive packet and octet counts if desired.
3.19 Register Interface
3.19.1 General
The Register Interface is a selectable 8/16-bit bidirectional data interface
that allows access to the internal registers.
3.19.2 Timing
The Register Interface consists of thirty seven signals: sixteen
bidirectional data I/O pins (CDST[15:0]), eight register address inputs
(A[7:0]), one chip select input (ENREGIO), one read select input (RD),
one write select input (WR), two port select inputs (REGPS[1:0], one bus
size select input (BUSSIZE), two byte enable inputs (BE[1:0]), one data
ready output (READY), and four interrupt outputs, one per port
(INT_[1:4]).
To access a register through the Register Interface, ENREGIO must first
be asserted active low. Then either RD or WR must be asserted active
low to indicate either a read or a write cycle. On that same falling edge
of either RD or WR, the address of the register that will be accessed
needs to be present on A[7:0], and the port to be selected must be
present on REGPS[1:0]. If the cycle is a write cycle (WR asserted), then
the data on CDST[15:0] will be written to the designated register. If the
cycle is a read cycle (RD asserted), then data from the designated
register will be output on CDST[15:0] after some delay after the falling
edge of RD. The READY output will then go active high to indicate that
the data on CDST[15:0] is valid. READY will stay high as long as RD is
asserted, and return low after RD is deasserted. READY is placed in high
impedance state when ENREGIO is deasserted and driven when
ENREGIO is asserted. ENREGIO can remain low for multiple read or
write cycles so that many registers can be read or written to in one
ENREGIO assertion.
相關PDF資料
PDF描述
L8560 Low-Power SLIC with Ringing
L8567 SLIC for Peoples Republic of China Applications
L8567-32PLCC Telecommunication IC
L8567-44PLCC Telecommunication IC
L8574D CAP 15PF 50V 5% C0G SMD-0402 TR-7-PA SN100
相關代理商/技術參數
參數描述
L8446-04 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES
L8446-06 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES
L8446-07 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES
L8446-41 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES
L8446-42 制造商:HAMAMATSU 制造商全稱:Hamamatsu Corporation 功能描述:CW LASER DIODES
主站蜘蛛池模板: 葵青区| 杨浦区| 策勒县| 南漳县| 柯坪县| 论坛| 扶余县| 宜都市| 绥棱县| 玉环县| 柞水县| 惠州市| 抚宁县| 马尔康县| 德昌县| 朔州市| 汕头市| 巴里| 寿宁县| 香格里拉县| 蓝田县| 肇东市| 襄城县| 永靖县| 海门市| 咸宁市| 延川县| 城固县| 陇川县| 遵义市| 宜黄县| 盖州市| 新沂市| 额济纳旗| 白沙| 独山县| 沈丘县| 阳曲县| 瓮安县| 武夷山市| 昌平区|