- 您現在的位置：買賣IC網 > PDF目錄371053 > MC68HC916X1 (Motorola, Inc.) 16-Bit Modular Microcontroller(16位模塊化微控制器) PDF資料下載
參數資料
| 型號： | MC68HC916X1 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 16-Bit Modular Microcontroller(16位模塊化微控制器) |
| 中文描述： | 16位微控制器模塊（16位模塊化微控制器） |
| 文件頁數： | 134/172頁 |
| 文件大小： | 1035K |
| 代理商： | MC68HC916X1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁當前第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁
MOTOROLA
134
MC68HC916X1
MC68HC916X1TS/D
10.2 BEFLASH Control Block
The BEFLASH module control block contains five registers: the BEFLASH module configuration
register (BFEMCR), the BEFLASH test register (BFETST), the BEFLASH array base address reg-
isters (BFEBAH and BFEBAL), and the BEFLASH control register (BFECTL). Four additional words
in the control block can contain bootstrap information when the BEFLASH is used as bootstrap
memory.
Each register in the control block has an associated shadow register that is physically located in a
spare BEFLASH row. During reset, fields within the registers are loaded with default information
from the shadow registers. Shadow registers are programmed or erased in the same manner as
locations in the BEFLASH array, using the address of the corresponding control registers. When a
shadow register is programmed, the data is not written to the corresponding control register. The
new data is not copied into the control register until the next reset. The contents of shadow registers
are erased whenever the BEFLASH array is erased.
Configuration information is specified and programmed independently of the BEFLASH array. After
reset, registers in the control block that contain writable bits can be modified. Writes to these reg-
isters do not affect the associated shadow register. Certain registers are writable only when the
LOCK bit in BFEMCR is disabled or when the STOP bit in BFEMCR is set. These restrictions are
noted in the individual register descriptions.
10.3 BEFLASH Array
The base address registers specify the starting address of the BEFLASH array. A default base ad-
dress can be programmed into the base address shadow registers. The array base address must
be on a 2 Kbyte boundary. Because the states of ADDR[23:20] follow the state of ADDR19, ad-
dresses in the range $080000 to $F7FFFF cannot be accessed by the CPU16. If the BEFLASH ar-
ray is mapped to these addresses, the system must be reset before the array can be accessed.
Avoid using a base address value that causes the array to overlap control registers. If a portion of
the array overlaps the EEPROM register block, the registers remain accessible, but accesses to
that portion of the array are ignored. If the array overlaps the control block of another module, how-
ever, those registers may become inaccessible. If the BEFLASH array overlaps another memory
array (RAM or flash EEPROM), proper access to one or both arrays may not be possible.
10.4 BEFLASH Registers
In the following register diagrams, the reset value SB indicates that a bit assumes the value of its
associated shadow bit during reset.
This register can be written only when the control block is not write-locked (when LOCK = 0). All
active bits take values from the associated shadow register during reset.
STOP — Stop Mode Control
0 = Normal operation
1 = Low-power stop operation
STOP can be set either by pulling data bus pin DATA15 low during reset or by the corresponding shad-
ow bit. The EEPROM array is inaccessible during low-power stop. The array can be re-enabled by
BFEMCR
— BEFLASH Module Configuration Register
$YFF7A0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
STOP
FRZ
0
BOOT
LOCK
0
ASPC[1:0]
0
0
0
0
0
0
0
0
RESET:
DATA15 +
SB
0
0
SB
SB
0
SB
SB
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC9D60 | Advance Information - Rev 4.0 |
| MC68HC12D60 | Advance Information - Rev 4.0 |
| MC68HCL05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HSC05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HCP11 | 8-Bit Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC98LJ12CFU | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
| MC68HC98LJ12CFUE | 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC9S08RC60 L33R DIE | 制造商:Motorola Inc 功能描述: |
| MC68HCP11A1CFN3 | 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11A1FN | 制造商:MOTORALA 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。