- 您現在的位置：買賣IC網 > PDF目錄371053 > MC68HC916X1 (Motorola, Inc.) 16-Bit Modular Microcontroller(16位模塊化微控制器) PDF資料下載
參數資料
| 型號： | MC68HC916X1 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 16-Bit Modular Microcontroller(16位模塊化微控制器) |
| 中文描述： | 16位微控制器模塊（16位模塊化微控制器） |
| 文件頁數： | 32/172頁 |
| 文件大小： | 1035K |
| 代理商： | MC68HC916X1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁
MOTOROLA
32
MC68HC916X1
MC68HC916X1TS/D
It is not possible to perform transfers of word operands to an 8-bit port on the MC68HC916X1 be-
cause the DSACK0 pin is not present and therefore cannot be asserted to acknowledge the trans-
fer. This limitation can be overcome by using SCIM chip-select logic to generate DSACK for such
transfers.
3.7 Resets
Reset procedures handle system initialization and recovery from catastrophic failure. The MCU per-
forms resets with a combination of hardware and software. The SCIM determines whether a reset
is valid, asserts control signals, performs basic system configuration and boot ROM selection based
on hardware mode-select inputs, then passes control to the CPU16.
Reset occurs when an active low logic level on the RESET pin is clocked into the SCIM. Resets are
gated by the CLKOUT signal. Asynchronous resets are assumed to be catastrophic. An asynchro-
nous reset can occur on any clock edge. Synchronous resets are timed to occur at the end of bus
cycles. If there is no clock when RESET is asserted, reset does not occur until the clock starts. Re-
sets are clocked to allow completion of write cycles in progress at the time RESET is asserted.
Reset is the highest-priority CPU16 exception. Any processing in progress is aborted by the reset
exception, and cannot be restarted. Only essential tasks are performed during reset exception pro-
cessing. Other initialization tasks must be accomplished by the exception handler routine.
3.7.1 SCIM Reset Mode Selection
The logic states of certain MCU pins during reset determine SCIM operating configuration. Refer to
3.2.1 Operating Modes
for more information.
3.7.2 MCU Module Pin Function During Reset
Module pins usually default to port functions, and input/output ports are set to input state. This is
accomplished by disabling pin functions in the appropriate control registers, and by clearing the ap-
propriate port data direction registers. For more information, refer to the sections of this technical
summary that present information about the individual modules.
Table 20
is a summary of module
pin functions out of reset.
1. Operands in parentheses are ignored by the CPU16 during read cycles.
2. Three-byte transfer cases occur only as a result of long word to byte transfer.
3. The CPU16 treats misaligned long-word transfers as two misaligned word transfers.
Table 19 Operand Alignment
Transfer Case
SIZ1
0
0
SIZ0
1
1
ADDR0
0
1
DATA[15:8]
OP0
(OP0)
1
OP0
(OP0)
1
OP0
(OP0)
1
OP0
(OP0)
1
DATA[7:0]
(OP0)
1
OP0
Byte to 16-Bit Port (Even)
Byte to 16-Bit Port (Odd)
Word to 16-Bit Port (Aligned)
Word to 16-Bit Port (Misaligned)
3 Byte to 16-Bit Port (Aligned)
2
3 Byte to 16-Bit Port (Misaligned)
2
Long Word to 16-Bit Port (Aligned)
Long Word to 16-Bit Port (Misaligned)
3
1
1
0
0
0
1
OP1
OP0
1
1
1
1
0
1
OP1
OP0
0
1
0
0
0
1
OP1
OP0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC9D60 | Advance Information - Rev 4.0 |
| MC68HC12D60 | Advance Information - Rev 4.0 |
| MC68HCL05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HSC05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| MC68HCP11 | 8-Bit Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC98LJ12CFU | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
| MC68HC98LJ12CFUE | 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC9S08RC60 L33R DIE | 制造商:Motorola Inc 功能描述: |
| MC68HCP11A1CFN3 | 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HCP11A1FN | 制造商:MOTORALA 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。