欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68HC916X1
廠商: Motorola, Inc.
英文描述: 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述: 16位微控制器模塊(16位模塊化微控制器)
文件頁數: 28/172頁
文件大小: 1035K
代理商: MC68HC916X1
MOTOROLA
28
MC68HC916X1
MC68HC916X1TS/D
3.4.2 Halt Monitor
The halt monitor responds to an assertion of HALT on the internal bus, caused by a double bus
fault. This signal is asserted by the CPU after a double bus fault occurs. A flag in the reset status
register (RSR) indicates that the last reset was caused by the halt monitor. The halt monitor reset
can be inhibited by the HME bit in the SYPCR.
3.4.3 Spurious Interrupt Monitor
The spurious interrupt monitor causes a bus error exception if no interrupt arbitration occurs during
an interrupt acknowledge cycle. The most common cause of spurious interrupts is failure to set the
module configuration register IARB[3:0] to a non-zero value for modules that can generate inter-
rupts.
3.4.4 Software Watchdog
The software watchdog service register (SWSR) is controlled by SWE in SYPCR. Once enabled,
the watchdog requires that a service sequence be written to SWSR on a periodic basis. If servicing
does not take place, the watchdog times out and issues a reset. This register can be written at any
time, but returns zeros when read.
Each time the service sequence is written, the software watchdog timer restarts. The sequence to
restart consists of the following steps:
Write $55 to SWSR
Write $AA to SWSR
Both writes must occur before timeout in the order listed, but any number of instructions, up to the
end of the timeout period, can be executed between the two writes.
Watchdog clock rate is affected by SWP and SWT[1:0] in SYPCR.
When SWT[1:0] are modified, a watchdog service sequence must be performed before the new
time-out period will take effect.
The reset value of SWP is the complement of the state of the MODCLK pin on the rising edge of
reset.
Software watchdog time-out period is given in the following equation:
3.5 External Bus Interface
The external bus interface (EBI) transfers information between the internal MCU bus and external
devices when the MCU is operating in expanded modes. In 16-bit expanded mode, the external bus
has 24 address lines and 16 data lines. In 8-bit expanded mode, the external bus has 24 address
lines and 8 data lines. Because the CPU16 drives only 20 of the 24 IMB address lines, ADDR[23:20]
follow the output state of ADDR19.
SWSR
— Software Watchdog Service Register
$YFFA27
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
UNUSED
SWSR
RESET:
0
0
0
0
0
0
0
0
Timeout Period
Divide Ratio Specified by SWP and SWT[1:0]
fref
-----------------------------------------------------------------------------------------------------------------------
=
相關PDF資料
PDF描述
MC68HC9D60 Advance Information - Rev 4.0
MC68HC12D60 Advance Information - Rev 4.0
MC68HCL05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HSC05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HCP11 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
主站蜘蛛池模板: 静宁县| 六枝特区| 丰原市| 抚宁县| 乌兰县| 厦门市| 得荣县| 堆龙德庆县| 枝江市| 清丰县| 定远县| 子洲县| 留坝县| 确山县| 正蓝旗| 新野县| 凉城县| 蕲春县| 措勤县| 麻阳| 兴化市| 伊川县| 信阳市| 梓潼县| 蒙自县| 弋阳县| 澄迈县| 乐都县| 河北省| 普洱| 河西区| 微博| 石河子市| 视频| 且末县| 淮阳县| 丰镇市| 都江堰市| 芜湖县| 通化市| 宁强县|