欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 106/128頁
文件大小: 748K
代理商: MC68B912B32
MOTOROLA
106
MC68HC912B32
MC68HC912B32TS/D
Read and write anytime.
DDDLC[6:0] — Data Direction Port DLC Pin 6 through Pin 0
0 = Configure I/O pin for input only
1 = Configure I/O pin for output
14.5 J1850 Bus Errors
The BDLC detects several types of transmit and receive errors which can occur during the transmission
of a message onto the J1850 bus.
If the BDLC transmits a message containing invalid bits, or framing symbols on non-byte boundaries,
then a transmission error has occurred. When a transmission error is detected, the BDLC will immedi-
ately cease transmitting. The error condition is reflected in the BSVR register. If the interrupt enable bit
(IE) is set, an interrupt request from the BDLC is generated.
CRC Error
— A CRC error is detected when the data bytes and CRC byte of a received message are
processed, and the CRC calculation result is not equal to $C4. The CRC code should detect any single
and 2-bit errors, as well as all 8-bit burst errors, and almost all other types of errors. CRC error flag is
set when a CRC error is detected.
Symbol Error
— A symbol error is detected when an abnormal (invalid) symbol is detected in a mes-
sage being received from the J1850 bus. However, if the BDLC is transmitting when this happens, it
may be treated as a loss of arbitration rather than a transmitter error. Symbol invalid or out of range flag
is set when a symbol error is detected.
Framing Error
— A framing error is detected if an EOD or EOF symbol is detected on a non-byte
boundary from the J1850 bus. Symbol invalid or out of range flag is set when a framing error is detected.
Bus Fault
— If a bus fault occurs, the response of the BDLC will depend upon the type of bus fault.
If the bus is shorted to V
BATT
, the BDLC will wait for the bus to fall to a passive state before it will attempt
to transmit a message. As long as the short remains, the BDLC will never attempt to transmit a message
onto the J1850 bus.
If the bus is shorted to ground, the BDLC will see an idle bus, begin to transmit the message, and then
detect a transmission error, since the short to ground would not allow the bus to be driven to the active
(dominant) state. The BDLC will abort that transmission and wait for the next CPU command to transmit.
In any case, if the bus fault is temporary, as soon as the fault is cleared, the BDLC will resume normal
operation. If the bus fault is permanent, it may result in permanent loss of communication on the J1850
bus.
BREAK
— Any BDLC transmitting at the time a BREAK is detected will treat the BREAK as if a trans-
mission error had occurred, and halt transmission.
If while receiving a message the BDLC detects a BREAK symbol, it will treat the BREAK as a reception
error.
DDRDLC
— Port DLC Data Direction Register
$00FF
Bit 7
6
5
4
3
2
1
Bit 0
0
DDDLC6
DDDLC5
DDDLC4
DDDLC3
DDDLC2
DDDLC1
DDDLC0
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 江永县| 津南区| 凯里市| 德惠市| 阿坝| 房山区| 营口市| 凌海市| 宁武县| 富顺县| 嵊州市| 朝阳县| 宿迁市| 石门县| 报价| 宁城县| 扶绥县| 枣强县| 沁水县| 射洪县| 富民县| 衢州市| 河西区| 紫阳县| 广东省| 灵璧县| 永州市| 河间市| 平安县| 金山区| 靖远县| 荥阳市| 时尚| 抚州市| 政和县| 铜鼓县| 靖边县| 浦县| 石屏县| 仁化县| 清流县|