欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 40/128頁
文件大小: 748K
代理商: MC68B912B32
MOTOROLA
40
MC68HC912B32
MC68HC912B32TS/D
ENPE — Enable Programming/Erase
0 = Disables program/erase voltage to Flash EEPROM
1 = Applies program/erase voltage to Flash EEPROM
ENPE can be asserted only after LAT has been asserted and a write to the data and address latches
has occurred. If an attempt is made to assert ENPE when LAT is negated, or if the latches have not
been written to after LAT was asserted, ENPE will remain negated after the write cycle is complete.
The LAT, ERAS and BOOTP bits cannot be changed when ENPE is asserted. A write to FEECTL may
only affect the state of ENPE. Attempts to read a Flash EEPROM array location in the Flash EEPROM
module while ENPE is asserted will not return the data addressed. See
Table 14
for more information.
Flash EEPROM module control registers may be read or written while ENPE is asserted. If ENPE is
asserted and LAT is negated on the same write access, no programming or erasure will be performed.
7.5 Operation
The Flash EEPROM can contain program and data. On reset, it can operate as a bootstrap memory to
provide the CPU with internal initialization information during the reset sequence.
7.5.1 Bootstrap Operation Single-Chip Mode
After reset, the CPU controlling the system will begin booting up by fetching the first program address
from address $FFFE.
7.5.2 Normal Operation
The Flash EEPROM allows a byte or aligned word read/write in one bus cycle. Misaligned word read/
write require an additional bus cycle. The Flash EEPROM array responds to read operations only. Write
operations are ignored.
7.5.3 Program/Erase Operation
An unprogrammed Flash EEPROM bit has a logic state of one. A bit must be programmed to change
its state from one to zero. Erasing a bit returns it to a logic one. The Flash EEPROM has a minimum
program/erase life of 100 cycles. Programming or erasing the Flash EEPROM is accomplished by a se-
ries of control register writes and a write to a set of programming latches.
Programming is restricted to a single byte or aligned word at a time as determined by internal signal
SZ8 and ADDR[0]. The Flash EEPROM must first be completely erased prior to programming final data
values. It is possible to program a location in the Flash EEPROM without erasing the entire array if the
new value does not require the changing of bit values from zero to one.
Read/Write Accesses During Program/Erase
— During program or erase operations, read and write
accesses may be different from those during normal operation and are affected by the state of the con-
trol bits in the Flash EEPROM control register (FEECTL). The next write to any valid address to the ar-
ray after LAT is set will cause the address and data to be latched into the programming latches. Once
the address and data are latched, write accesses to the array will be ignored while LAT is set. Writes to
the control registers will occur normally.
Program/Erase Verification
— When programming or erasing the Flash EEPROM array, a special
verification method is required to ensure that the program/erase process is reliable, and also to provide
Table 14 Effects of ENPE, LAT and ERAS on Array Reads
ENPE
0
0
0
1
LAT
0
1
1
ERAS
0
1
Result of Read
Normal read of location addressed
Read of location being programmed
Normal read of location addressed
Read cycle is ignored
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 六枝特区| 任丘市| 万源市| 东港市| 手游| 贵德县| 襄樊市| 赫章县| 奎屯市| 梓潼县| 蓬溪县| 涿鹿县| 蒲江县| 明光市| 房山区| 阿拉善右旗| 桃源县| 民乐县| 新晃| 榕江县| 葵青区| 张掖市| 多伦县| 山西省| 扎赉特旗| 寿宁县| 白水县| 南溪县| 玉门市| 六安市| 金阳县| 通榆县| 桐柏县| 广宗县| 杭州市| 广水市| 宁南县| 铅山县| 永宁县| 合川市| 龙岩市|