欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 46/128頁
文件大小: 748K
代理商: MC68B912B32
MOTOROLA
46
MC68HC912B32
MC68HC912B32TS/D
7.8 Program/Erase Protection Interlocks
The Flash EEPROM program and erase mechanisms provide maximum protection from accidental pro-
gramming or erasure.
The voltage required to program/erase the Flash EEPROM (V
FP
) is supplied via an external pin. If V
FP
is not present, no programming/erasing will occur. Furthermore, the program/erase voltage will not be
applied to the Flash EEPROM unless turned on by setting a control bit (ENPE). The ENPE bit may not
be set unless the programming address and data latches have been written previously with a valid ad-
dress. The latches may not be written unless enabled by setting a control bit (LAT). The LAT and ENPE
control bits must be written on separate writes to the control register (FEECTL) and must be separated
by a write to the programming latches. The ERAS and LAT bits are also protected when ENPE is set.
This prevents inadvertent switching between erase/program mode and also prevents the latched data
and address from being changed after a program cycle has been initiated.
7.9 Stop or Wait Mode
When stop or wait commands are executed, the MCU puts the Flash EEPROM in stop or wait mode. In
these modes the Flash module will cease erasure or programming immediately. It is advised not to enter
stop or wait modes when programming the Flash array.
CAUTION
The Flash EEPROM module is not able to recover from STOP without a 1 micro-
second delay. This cannot be controlled internal to the MCU. Therefore, do not at-
tempt to recover from STOP with an interrupt. Use RESET to recover from a STOP
mode executed from Flash EEPROM. Recovery from a STOP instruction executed
from EEPROM and RAM operate normally.
7.10 Test Mode
The Flash EEPROM has some special test functions which are only accessible when the device is in
test mode.
Test mode is indicated to the Flash EEPROM module when the SMOD line on the LIB is
asserted. When SMOD is asserted, the special test control bits may be accessed via the LIB to invoke
the special test functions in the Flash EEPROM module. When SMOD is not asserted, writes to the test
control bits have no effect and all bits in the test register FEETST will be cleared. This ensures that
Flash EEPROM test mode cannot be invoked inadvertently during normal operation.
Note that the Flash EEPROM module will operate normally, even if SMOD is asserted, until a special
test function is invoked. The test mode adds additional features over normal mode which allow the tests
to be performed even after the device is installed in the final product.
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 陇川县| 县级市| 抚松县| 延边| 普定县| 志丹县| 呼伦贝尔市| 杭州市| 南丰县| 繁峙县| 达日县| 中牟县| 闸北区| 保山市| 乳山市| 临沧市| 东阿县| 元阳县| 秀山| 衢州市| 普宁市| 曲靖市| 青田县| 高邮市| 眉山市| 南郑县| 翼城县| 乌拉特中旗| 平顶山市| 天峻县| 茶陵县| 新田县| 通海县| 庆云县| 承德市| 林周县| 十堰市| 长阳| 新津县| 全南县| 宁武县|