欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 39/128頁
文件大小: 748K
代理商: MC68B912B32
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
39
STRE — Spare Test Row Enable
The spare test row consists of one Flash EEPROM array row. The reserved word at location 31 contains
production test information which must be maintained through several erase cycles. When STRE is set,
the decoding for the spare test row overrides the address lines which normally select the other rows in
the array.
0 = LIB accesses are to the Flash EEPROM array
1 = Spare test row in array enabled if SMOD is active
MWPR — Multiple Word Programming
Used primarily for testing, if MPWR = 1, the two least-significant address lines ADDR[1:0] will be ignored
when programming a Flash EEPROM location. The word location addressed if ADDR[1:0] = 00, along
with the word location addressed if ADDR[1:0] = 10, will both be programmed with the same word data
from the programming latches. This bit should not be changed during programming.
0 = Multiple word programming disabled
1 = Program 32 bits of data
This register controls the programming and erasure of the Flash EEPROM.
FEESWAI — Flash EEPROM Stop in Wait Control
0 = Do not halt Flash EEPROM clock when the part is in wait mode.
1 = Halt Flash EEPROM clock when the part is in wait mode.
NOTE
The FEESWAI bit cannot be asserted if the interrupt vector resides in theFlash
EEPROM array.
SVFP — Status V
FP
Voltage
SVFP is a read only bit.
0 = Voltage of V
FP
pin is below normal programming voltage levels
1 = Voltage of V
FP
pin is above normal programming voltage levels
ERAS — Erase Control
This bit can be read anytime or written when ENPE = 0. When set, all locations in the array will be
erased at the same time. The boot block will be erased only if BOOTP = 0. This bit also affects the result
of attempted array reads. See
Table 14
for more information. Status of ERAS cannot change if ENPE
is set.
0 = Flash EEPROM configured for programming
1 = Flash EEPROM configured for erasure
LAT — Latch Control
This bit can be read anytime or written when ENPE = 0. When set, the Flash EEPROM is configured
for programming or erasure and, upon the next valid write to the array, the address and data will be
latched for the programming sequence. See
Table 14
for the effects of LAT on array reads. A high volt-
age detect circuit on the V
FP
pin will prevent assertion of the LAT bit when the programming voltage is
at normal levels.
0 = Programming latches disabled
1 = Programming latches enabled
FEECTL
— Flash EEPROM Control Register
$00F7
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
FEESWAI
SVFP
ERAS
LAT
ENPE
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 遂平县| 宜兰县| 颍上县| 顺平县| 佳木斯市| 老河口市| 渭南市| 沙坪坝区| 寿宁县| 台安县| 清水县| 凤庆县| 易门县| 开封县| 碌曲县| 夹江县| 神农架林区| 宝丰县| 巴彦淖尔市| 张掖市| 石景山区| 筠连县| 永宁县| 莲花县| 防城港市| 邢台市| 南昌县| 灵宝市| 开江县| 万山特区| 喜德县| 田阳县| 渝中区| 改则县| 武定县| 夏津县| 大丰市| 哈巴河县| 同心县| 淮滨县| 芦溪县|