欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 115/128頁
文件大小: 748K
代理商: MC68B912B32
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
115
16 Development Support
Development support involves complex interactions between MC68HC912B32 resources and external
development systems. The following section concerns instruction queue and queue tracking signals,
background debug mode, and instruction tagging.
16.1 Instruction Queue
The CPU12 instruction queue provides at least three bytes of program information to the CPU when
instruction execution begins. The CPU12 always completely finishes executing an instruction before be-
ginning to execute the next instruction. Status signals IPIPE[1:0] provide information about data move-
ment in the queue and indicate when the CPU begins to execute instructions. This makes it possible to
monitor CPU activity on a cycle-by-cycle basis for debugging. Information available on the IPIPE[1:0]
pins is time multiplexed. External circuitry can latch data movement information on rising edges of the
E-clock signal; execution start information can be latched on falling edges.
Table 42
shows the meaning
of data on the pins.
Program information is fetched a few cycles before it is used by the CPU. In order to monitor cycle-by-
cycle CPU activity, it is necessary to externally reconstruct what is happening in the instruction queue.
Internally the MCU only needs to buffer the data from program fetches. For system debug it is necessary
to keep the data and its associated address in the reconstructed instruction queue. The raw signals re-
quired for reconstruction of the queue are ADDR, DATA, R/W, ECLK, and status signals IPIPE[1:0].
The instruction queue consists of two 16-bit queue stages and a holding latch on the input of the first
stage. To advance the queue means to move the word in the first stage to the second stage and move
the word from either the holding latch or the data bus input buffer into the first stage. To start even (or
odd) instruction means to execute the opcode in the high-order (or low-order) byte of the second stage
of the instruction queue.
16.2 Background Debug Mode
Background debug mode (BDM) is used for system development, in-circuit testing, field testing, and
programming. BDM is implemented in on-chip hardware and provides a full set of debug options.
Because BDM control logic does not reside in the CPU, BDM hardware commands can be executed
while the CPU is operating normally. The control logic generally uses CPU dead cycles to execute these
NOTES:
1. Refers to data that was on the bus at the previous E falling edge.
2. Refers to bus cycle starting at this E falling edge.
Table 42 IPIPE Decoding
Data Movement — IPIPE[1:0] Captured at Rising Edge of E Clock
1
IPIPE[1:0]
Mnemonic
0:0
0:1
LAT
1:0
ALD
1:1
ALL
Execution Start — IPIPE[1:0] Captured at Falling Edge of E Clock
2
IPIPE[1:0]
Mnemonic
0:0
0:1
INT
1:0
SEV
1:1
SOD
Meaning
No Movement
Latch Data From Bus
Advance Queue and Load From Bus
Advance Queue and Load From Latch
Meaning
No Start
Start Interrupt Sequence
Start Even Instruction
Start Odd Instruction
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 崇礼县| 郴州市| 安庆市| 新民市| 朝阳区| 屯留县| 安达市| 全南县| 佛山市| 云安县| 鹿邑县| 厦门市| 南皮县| 东乡族自治县| 水城县| 治县。| 翁牛特旗| 尉犁县| 石城县| 米泉市| 香河县| 呼伦贝尔市| 皮山县| 宁海县| 柯坪县| 永靖县| 抚宁县| 明水县| 曲沃县| 陇南市| 安达市| 哈巴河县| 大渡口区| 资阳市| 什邡市| 娄底市| 明光市| 太和县| 石屏县| 商城县| 东丰县|