欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68B912B32
廠商: Motorola, Inc.
英文描述: 2.5V 100ppm/Degrees C, 50uA in SOT23-3 Series (Bandgap) Voltage Reference 3-SOT-23 -40 to 125
中文描述: 16位微控制器
文件頁數: 96/128頁
文件大小: 748K
代理商: MC68B912B32
MOTOROLA
96
MC68HC912B32
MC68HC912B32TS/D
(read or write) to the SP0DR register.
0 = No write collision
1 = Indicates that a serial transfer was in progress when the MCU tried to write new data into the
SP0DR data register.
MODF — SPI Mode Error Interrupt Status Flag
This bit is set automatically by SPI hardware if the MSTR control bit is set and the slave select input pin
becomes zero. This condition is not permitted in normal operation. In the case where DDRS bit 7 is set,
the PS7 pin is a general-purpose output pin or SS output pin rather than being dedicated as the SS input
for the SPI system. In this special case the mode fault function is inhibited and MODF remains cleared.
This flag is automatically cleared by a read of the SP0SR (with MODF set) followed by a write to the
SP0CR1 register.
Read anytime (normally only after SPIF flag set). Write anytime (see WCOL write collision flag).
Reset does not affect this address.
This 8-bit register is both the input and output register for SPI data. Reads of this register are double
buffered but writes cause data to be written directly into the serial shifter. In the SPI system the 8-bit
data register in the master and the 8-bit data register in the slave are linked by the MOSI and MISO
wires to form a distributed 16-bit register. When a data transfer operation is performed, this 16-bit reg-
ister is serially shifted eight bit positions by the SCK clock from the master so the data is effectively ex-
changed between the master and the slave. Note that some slave devices are very simple and either
accept data from the master without returning data to the master or pass data to the master without re-
quiring data from the master.
13.4 Port S
In all modes, port S bits PS[7:0] can be used for either general-purpose I/O, or with the SCI and SPI
subsystems. During reset, port S pins are configured as high-impedance inputs (DDRS is cleared).
PORTS can be read anytime. When configured as an input, a read will return the pin level. When con-
figured as output, a read will return the latched output data. Writes do not change pin state when pin
configured for SPI or SCI output.
After reset all bits are configured as general-purpose inputs.
Port S shares function with the on-chip serial systems (SPI0 and SCI0).
Read or write anytime.
After reset, all general-purpose I/O are configured for input only.
0 = Configure the corresponding I/O pin for input only
1 = Configure the corresponding I/O pin for output
SP0DR
— SPI Data Register
$00D5
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
RESET:
0
0
0
0
0
0
0
0
PORTS
— Port S Data Register
$00D6
Bit 7
6
5
4
3
2
1
Bit 0
PS7
PS6
PS5
PS4
PS3
PS2
PS1
PS0
Pin
Function
SS
CS
SCK
MOSI
MOMI
MISO
SISO
I/O
I/O
TXD0
RXD0
DDRS
— Data Direction Register for Port S
$00D7
Bit 7
6
5
4
3
2
1
Bit 0
DDS7
DDS6
DDS5
DDS4
DDS3
DDS2
DDS1
DDS0
RESET:
0
0
0
0
0
0
0
0
相關PDF資料
PDF描述
MC68C912B32FU8 16-Bit Microcontroller
MC68B912B32FU8 16-Bit Microcontroller
MC68C912B32CFU8 16-Bit Microcontroller
MC68CK338 Highly Integrated, Low-Power, 32-Bit Microcontroller
MC68EC060 32-Bit Microprocessors.(32位微處理器)
相關代理商/技術參數
參數描述
MC68B912B32FU8 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller
MC68BOOL 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOP 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68BOOS 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU)
MC68C812A4 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics
主站蜘蛛池模板: 繁昌县| 佛学| 方山县| 镇沅| 普陀区| 烟台市| 郯城县| 丁青县| 连州市| 陇川县| 永兴县| 绥芬河市| 梅州市| 噶尔县| 武宁县| 菏泽市| 监利县| 邻水| 丰县| 东安县| 万安县| 东乡| 吉首市| 和硕县| 扎赉特旗| 西畴县| 吴川市| 淮南市| 开平市| 天全县| 瓦房店市| 贵德县| 三亚市| 阿图什市| 赞皇县| 天门市| 万盛区| 昌吉市| 铁岭县| 云南省| 红原县|