欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68CK338
廠商: Motorola, Inc.
元件分類: 32位微控制器
英文描述: Highly Integrated, Low-Power, 32-Bit Microcontroller
中文描述: 高度集成,低功耗,32位微控制器
文件頁數: 44/133頁
文件大小: 798K
代理商: MC68CK338
MOTOROLA
44
MC68CK338
MC68CK338TS/D
If an internal source asserts the reset signal, the reset control logic asserts RESET for a minimum of
512 cycles. If the reset signal is still asserted at the end of 512 cycles, the control logic continues to
assert RESET until the internal reset signal is negated.
After 512 cycles have elapsed, the reset input pin goes to an inactive, high-impedance state for 10 cy-
cles. At the end of this 10-cycle period, the reset input is tested. When the input is at logic level one,
reset exception processing begins. If, however, the reset input is at logic level zero, the reset control
logic drives the pin low for another 512 cycles. At the end of this period, the pin again goes to high-
impedance state for ten cycles, then it is tested again. The process repeats until RESET is released.
3.8.5 Power-On Reset
When the SIML clock synthesizer is used to generate the system clock, power-on reset involves special
circumstances related to application of system and clock synthesizer power. Regardless of clock
source, voltage must be applied to clock synthesizer power input pin V
DDSYN
in order for the MCU to
operate. The following discussion assumes that V
DDSYN
is applied before and during reset. This mini-
mizes crystal start-up time. When V
DDSYN
is applied at power-on, start-up time is affected by specific
crystal parameters and by oscillator circuit design. V
DD
ramp-up time also affects pin state during reset.
During power-on reset, an internal circuit in the SIML drives the IMB and external reset lines. The circuit
releases the internal reset line as V
DD
ramps up to the minimum specified value, and SIML pins are
initialized. As V
DD
reaches a specified minimum value, the clock synthesizer VCO begins operation and
clock frequency ramps up to specified limp mode frequency. The external RESET line remains asserted
until the clock synthesizer PLL locks and 512 CLKOUT cycles elapse.
The SIML clock synthesizer provides clock signals to the other MCU modules. After the clock is running
and the internal reset signal is asserted for four clock cycles, these modules reset. V
DD
ramp time and
VCO frequency ramp time determine how long these four cycles take. Worst case is approximately 15
milliseconds. During this period, module port pins may be in an indeterminate state. While input-only
pins can be put in a known state by means of external pull-up resistors, external logic on input/output
or output-only pins must condition the lines during this time. Active drivers require high-impedance buff-
ers or isolation resistors to prevent conflict.
3.8.6 Use of Three-State Control Pin
Asserting the three-state control (TSC) input causes the MCU to put all output drivers in an inactive,
high-impedance state. The signal must remain asserted for ten clock cycles in order for drivers to
change state. There are certain constraints on use of TSC during power-on reset:
When the internal clock synthesizer is used (MODCLK held high during reset), synthesizer ramp-
up time affects how long the ten cycles take. Worst case is approximately 20 ms from TSC asser-
tion.
When an external clock signal is applied (MODCLK held low during reset), pins go to high-imped-
ance state as soon after TSC assertion as ten clock pulses have been applied to the EXTAL pin.
When TSC assertion takes effect, internal signals are forced to values that can cause inadvertent
mode selection. Once the output drivers change state, the MCU must be powered down and re-
started before normal operation can resume.
3.9 Interrupts
Interrupt recognition and servicing involve complex interaction between the CPU32L, the SIML, and a
device or module requesting interrupt service.
相關PDF資料
PDF描述
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
MC68EN360CFE25 QUad Integrated Communications Controller Users Manual
MC68EN360FE25 AC 4C 4#12 PIN PLUG 023
MC68EN360FE25V QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68CK338CPV14 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68CK338CPV14B1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:32-Bit Modular Microcontroller
MC68CM16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CPV16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
主站蜘蛛池模板: 闵行区| 神农架林区| 嘉定区| 长乐市| 禄劝| 玉树县| 郁南县| 洪泽县| 宁河县| 安福县| 温宿县| 湖南省| 武隆县| 新巴尔虎右旗| 杭锦旗| 阜宁县| 弥渡县| 鹤壁市| 涟水县| 报价| 井陉县| 湄潭县| 龙川县| 道孚县| 昌都县| 西峡县| 莱州市| 古蔺县| 武安市| 玛曲县| 卓尼县| 会东县| 嫩江县| 昌黎县| 寻甸| 清水河县| 平远县| 雅安市| 奉节县| 上饶市| 闽侯县|