欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC68CK338
廠商: Motorola, Inc.
元件分類: 32位微控制器
英文描述: Highly Integrated, Low-Power, 32-Bit Microcontroller
中文描述: 高度集成,低功耗,32位微控制器
文件頁數: 46/133頁
文件大小: 798K
代理商: MC68CK338
MOTOROLA
46
MC68CK338
MC68CK338TS/D
Arbitration is performed by means of serial contention between values stored in individual module inter-
rupt arbitration (IARB) fields. Each module that can make an interrupt service request, including the
SIML, has an IARB field in its configuration register. IARB fields can be assigned values from %0000
to %1111. In order to implement an arbitration scheme, each module that can initiate an interrupt ser-
vice request must be assigned a unique, non-zero IARB field value during system initialization. Arbitra-
tion priorities range from %0001 (lowest) to %1111 (highest) — if the CPU recognizes an interrupt
service request from a source that has an IARB field value of %0000, a spurious interrupt exception is
processed.
WARNING
Do not assign the same arbitration priority to more than one module. When two or
more IARB fields have the same non-zero value, the CPU32L interprets multiple
vector numbers at the same time, with unpredictable consequences.
Because the EBI manages external interrupt requests, the SIML IARB value is used for arbitration be-
tween internal and external interrupt requests. The reset value of IARB for the SIML is %1111, and the
reset IARB value for all other modules is %0000.
Although arbitration is intended to deal with simultaneous requests of the same priority, it always takes
place, even when a single source is requesting service. This is important for two reasons: the EBI does
not transfer the interrupt acknowledge read cycle to the external bus unless the SIML wins contention,
and failure to contend causes the interrupt acknowledge bus cycle to be terminated early, by a bus error.
When arbitration is complete, the module with the highest arbitration priority must terminate the bus
cycle. Internal modules place an interrupt vector number on the data bus and generate appropriate in-
ternal cycle termination signals. In the case of an external interrupt request, after the interrupt acknowl-
edge cycle is transferred to the external bus, the appropriate external device must decode the mask
value and respond with a vector number, then generate data and size acknowledge (DSACK) termina-
tion signals, or it must assert the autovector (AVEC) request signal. If the device does not respond in
time, the EBI bus monitor asserts the bus error signal (BERR), and a spurious interrupt exception is
taken.
Chip-select logic can also be used to generate internal AVEC or DSACK signals in response to interrupt
requests from external devices. Chip-select address match logic functions only after the EBI transfers
an interrupt acknowledge cycle to the external bus following IARB contention. If a module makes an
interrupt request of a certain priority, and the appropriate chip-select registers are programmed to gen-
erate AVEC or DSACK signals in response to an interrupt acknowledge cycle for that priority level, chip-
select logic does not respond to the interrupt acknowledge cycle, and the internal module supplies a
vector number and generates internal cycle termination signals.
For periodic timer interrupts, the PIRQL field in the periodic interrupt control register (PICR) determines
PIT priority level. A PIRQL value of %000 means that PIT interrupts are inactive. By hardware conven-
tion, when the CPU32L receives simultaneous interrupt requests of the same level from more than one
SIML source (including external devices), the periodic interrupt timer is given the highest priority, fol-
lowed by the IRQ pins. Refer to
3.4.6 Periodic Interrupt Timer
for more information.
3.9.2 Interrupt Processing Summary
A summary of the interrupt processing sequence follows. When the sequence begins, a valid interrupt
service request has been detected and is pending.
相關PDF資料
PDF描述
MC68EC060 32-Bit Microprocessors.(32位微處理器)
MC68EN360RC25V QUad Integrated Communications Controller Users Manual
MC68EN360CFE25 QUad Integrated Communications Controller Users Manual
MC68EN360FE25 AC 4C 4#12 PIN PLUG 023
MC68EN360FE25V QUad Integrated Communications Controller Users Manual
相關代理商/技術參數
參數描述
MC68CK338CPV14 制造商:Rochester Electronics LLC 功能描述:- Bulk
MC68CK338CPV14B1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:32-Bit Modular Microcontroller
MC68CM16Z1 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CFC16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
MC68CM16Z1CPV16 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series
主站蜘蛛池模板: 长乐市| 乌什县| 襄汾县| 大城县| 山东| 甘洛县| 中卫市| 万山特区| 陕西省| 望奎县| 界首市| 营口市| 称多县| 贺州市| 东港市| 青田县| 手机| 分宜县| 盐源县| 天水市| 新邵县| 商丘市| 吉木萨尔县| 理塘县| 行唐县| 武平县| 长泰县| 洪江市| 修文县| 绿春县| 会泽县| 青海省| 陵川县| 灵石县| 介休市| 冕宁县| 绥中县| 兴文县| 宁陵县| 阜康市| 长沙市|